General Considerations; Introduction; Main Functions; Technical Specifications - Espa NCR Instrucciones De Uso

I N S T R U C T I O N M A N U A L
DANGER power-supply cable
Place the power-supply cable in such a way
that it cannot be walked upon, perforated or
damaged by any object in its vicinity.
Carry out the installation in accordance with
the safety recommendations for swimming
pools and the specific instructions for the
pump to be installed (not provided with the
equipment).
Current safety regulations must be complied
with when installing the equipment.
FORBIDDEN to work upon or repair.
Work or repairs must be carried out only by
official technical service centres.
Users can only carry out the work described in this
manual.
The manufacturer declines responsibility for any
work that may be carried out by the user.
IMPORTANT NOTE: cleaning.
Always clean with a cloth moistened with a
neutral soap solution. Do not use products
containing solvents or acids.
Do not run the pump dry; the swimming pool
water must cover the plate entirely.

2. GENERAL CONSIDERATIONS.

2.1. Introduction.

The swim-against-the-current unit is a piece of equip-
ment for swimming pools that propels a large jet of
water by means of an electric pump.
It is used for practising swimming against the current.
As an option, and by using a massage hosepipe (not
supplied), it can have the function of propelling, toge-
ther with the water, microbubbles which in contact with
the user's body provide a pleasant sensation with
hydrotherapeutic effects.
It is available with a round or square plate and the
possibility of fitting three different versions of wall-
mounted pump-control panel, depending on the
power supply or the power of the electric pump to be
installed.

2.2. Main functions.

a) Propulsion of water: with built-in manual adjus-
tment of water-jet flow and direction.
b) Propulsion of air bubbles: built-in control of bubbles
by choking off the passage of air, which by venturi
effect is propelled simultaneously with the water jet.
c) Pump Stop/Start switch: fitted with a pneumatic
push-button, which for reasons of electrical safety
remotely actuates the pneumatic switch on the con-
trol panel, thus stopping or starting the electric
pump.

2.3. Technical specifications.

Maximum admissible flow
Minimum recommended flow
Hydraulic connections
Electrical connections
Maximum current
3. INSTALLATION. (Fig. 1)
According to swimming pool construction type.

3.1. Panel-structure swimming pools.

a) Cutting the panel. (Fig. 2)
Remove the canvas from the panel.
Place the template (15) on the interior part of the
swimming pool panel, such that the distance betwe-
en the plane XY and the maximum height of the
structure is 400 mm. The plane XY must be parallel
to the maximum-height plane of the swimming pool.
Mark the 14 assembly holes and cut along the dot-
ted-line zone of the template so as to mark the cut
outline on the panel.
Cut the outline and drill the holes marked on the
panel.
Take care not to damage the canvas.
b) Pre-assembly, with the canvas removed from the
panel and according to the drawing:
Clean the contact surfaces between the gaskets
(2), rear body (3) and counterflange (1) and the
panel of the swimming pool.
Stick a gasket (2) onto the counterflange (1). (Fig. A)
Stick the remaining two gaskets (2) onto the rear
body (3) (according to drawing). (Fig. B - C)
Secure the counterflange (1) through the rear part
of the swimming pool panel, fit the rear body (3)
from the other side of the panel and hold it firmly in
place while the two screws (13) are driven into the
holes A and B. (Fig. D)
Ensure that the rear body (3) is in correct position.
The word "HAUT" must be at the top part. (Fig. E)
c) Assembly.
After fitting the canvas, fill the swimming pool with
approximately 15 cm of water so that it is well ten-
sioned.
Place the flange (5) on the canvas, seeking out the
right position and making use of the lip of the pro-
tective plate (4) to position it. Insert the screws (11)
so that they pierce the canvas and then drive them
fully home. Avoid excessive force when driving
home the screws. (Fig. F)
Once all the screws are secured, cut the interior
part of the canvas with a cutter. (Fig. G)
Remove the protective plate (4) and stow it safely.
(Fig. H)
7
80 m 3 /h
40 m /h
3
interior Ø 63
NC_M 1 ~ 230 V
NC_T_ 3 ~ 400 V
NC_M 16A
NC_T1 6.3A
NC_T2 10A