Festool VB-CS 50 Instrucciones De Montaje página 5

Table widener
[Figure 1/2/3]
Fitting the table widener (usually on the right-hand
side of the table) widens the saw table on the CS 50
EB/CMS GE by 410 mm.
Fitting
- Lower the table widener into position at an angle,
locating both plastic brackets (1.1) in the groove
(1.2) on the saw table.
Caution: the retaining plates (1.3) must be moved
to the rear position (away from the saw table).
- Guide the ends of the two support feet (2.3) into
the long holes (2.4) on the bench chassis.
- Secure the supporting arms with the two knurled
nuts (2.5)
- Slide both retaining plates (2.1) up to the stop
on the saw table and tighten both rotary knobs
(2.2).
Height adjustment
- Unscrew both rotary knobs (2.2).
- Turn both Allen screws (3.1) until the saw table
and the table widener are at the same height.
- Tighten the rotary knobs (2.2).
Adjusting the gradient
- Unscrew the lock nuts (2.6) on both supporting
arms
- Turn both nuts (2.7) until the saw table and the
table widener form a level surface (Note: Check
this by placing a straight rule across the saw table
and table widener).
- Tighten the lock nuts (2.6).
Adjusting the scale
- Unscrew the fastening screws (3.2).
- Slide the scale on the table widener (3.3) up to the
scale on the saw table.
- Tighten the fastening screws (3.2).
Alignment of the V-groove
Check after installation whether the pre-set profi le
setting rail can be pushed without any problems
between saw table and table widener.
If not:
- Position the pre-set profi le setting rail so that it
makes equal contact with the saw table and the
table widener.
- Unscrew the rotary knob (2.2) on both support
feet.
- Secure the angle stop in the specifi ed position.
- - Tighten the rotary button (2.2).
Removal
Removal should proceed in reverse order to the
fi tting process. Do not forget to slide the retaining
plates (2.1) to the rear position before removing the
table widener.
VB-CS 50/VB-CMS
5
Table lengthener
[Figure 4/5/6]
For more secure support when sawing longer work-
pieces, a table lengthener can be fi tted to extend the
CS 50 EB/CMS GE saw table by 420 mm.
- The table lengthener is fi tted to the back of the
table.
When the sliding table is installed, the extension
cannot be fi tted.
Fitting
- Secure both retainers (4.2) to the table chassis us-
ing the accompanying screw (4.1) and nut (4.5).
- Unscrew both rotary knobs (5.1).
- Mount the table lengthener from above at an angle,
inserting the threads (5.2) of both rotary knobs into
the slots (5.3) on the retainers
- Guide the ends of the two support feet (6.8) into
the long holes (6.6) on the bench chassis.
- Push down the table lengthener to the end position
in the holder.
- Tighten the rotary knobs (6.1) and knurled nuts
(6.7). Make sure that both the rotary knobs and
the supporting arms are located at the base of the
slots and elongated holes.
Height adjustment
- Unscrew the two screws (6.4) and lock nuts
(6.5).
- Turn both screws (6.4) until the saw table and the
table lengthener are at the same height.
- Tighten both screws (6.4) and lock nuts (6.5).
Adjusting the gradient
- Unscrew the lock nuts (6.3) on both supporting
arms
- Turn both nuts (6.2) until the saw table and the ta-
ble lengthener form an even surface (Note: Check
this by placing a straight rule across the saw table
and table lengthener).
- Tighten the lock nuts (6.3).
Removal
Removal should proceed in reverse order to the
fi tting process.
VL