Service And Maintenance - Festool RENOFIX RG 130 E Manual De Instrucciones Original

approx 3 – 5 min, the machine is fully loadable.
Heat protection for devices heated during opera-
tion, reacts adequately sooner.
7 Operation
7.1 Fastening the grinding wheel
 Clean the fl ange [2-1] and fastening nut [2-3],
as well as grinding wheel fastening areas [2-2].
 Mount grinding wheel [2-2]. Flange fitting
must fi t the grinding wheel aperture.
 Press in the spindle blocking plunger [1-6].
Press in the blocking plunger only when device
is switched off and spindle not active.
 Turn the spindle until blocking plunger fi ts in.
 Screw the fastening nut [2-3] by fi tting it from
the grinding wheel [2-2] on the spindle [2-5].
 Fasten the fastening nut [2-3] with key [2-4].
 Before starting the device, make sure the
grinding wheel rotates smoothly.
Use only grinding wheels recommended by the

manufacturer and designed fl ange, which are
included in the package.
7.2 Positioning the handle
Suffi ciently release the handle manual screw [1-
9] and tilt the handle [1-5] to set the most suitable
working position. Re-fasten the manual screw [1-9].
7.3 Dust suction
Always work with connected suction device. Insert
the suction device pipe into the suction extension
[1-3]. In order to increase the effi ciency, we rec-
ommend to use pipes with
Use solely suction devices with antistatic pipe

design.
7.4 Lifting the front brush
For wall lifting, it is possible to lift the lifting seg-
ment [3-1] – see fi gure [3].
7.5 Brush replacement
After wear and tear of the brush [4-1], it must be
replaced.
 At fi rst unscrew the screws with washers [4-2],
remove the brush from the cover [4-3] with the
springs [4-4].
 Insert the springs into the holes in the new
brush and secure the in the holes by turning
them clockwise – see fi gure [4 a]. Defl ecting
the springs from vertical direction does not
constitute a defect.
 Then remove the brush with fi tted springs, at-
tach them on the cover [4-3] from the front end
and tilt them – see fi gure [4 b].
 Make sure that the springs in the cover fi t into
36 mm.
the guiding holes and screw back the screws
with washers [4-2].
7.6 Grinding wheel
Depending on the application area, various grind-
ing wheels are available – see table on page 16
Use solely wheels of Festool trademark, which
guarantees the grinding output of the machine.
8

Service and maintenance

WARNING
Risk of accident, electric shock
 Always pull the plug out of the socket before
performing any type of work on the machine.
 All maintenance and repair work which re-
quires the motor housing to be opened, must
only be carried out by an authorised service
workshop.
- Wrapped electric tools can be stored in a dry
place without heating, with temperatures not
lower than −5 °C. Unwrapped electric tools can
only be stored in dry places with temperatures
not lower than +5 °C, without sudden changes
in the temperature.
- To ensure the airflow is sufficient, cooling
openings of the motor must be always clean
and free.
- The machine is equipped with special self-
disconnecting brushes. When the brushes are
worn, the power supply is automatically dis-
connected, and the machine is stopped.
Customer service and repair. Only through
manufacturer or service workshops:
Please fi nd the nearest address at: www.
festool.com/service
Use only original Festool spare parts! Or-
EKAT
4
der No. at:
5
3
2
1
www.festool.com/service
9 Environment
Do not throw the power tool in your household
waste! Dispose of the machine, accessories and
packaging at an environmentally-responsible re-
cycling centre! Observe the valid national regula-
tions.
EU only: In accordance with European Directive on
waste electrical and electronic equipment and im-
plementation in national law, used electric power
tools must be collected separately and handed in
for environmentally friendly recycling.
15