Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
IMPORTANT SAFETY INSTRUCTIONS FOR USE
OF THE CORDLESS IMPACT DRIVER/WRENCH
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of the cordless impact
driver/wrench. To avoid these risks, follow these
basic safety instructions:
1.
Never use this impact driver/wrench handle for any
application other than those in this manual.
2.
Never place hands or other body parts near the
drill bit or chuck during operation.
Hold the impact driver/wrench by its handle only.
3.
When working in high places, always make sure
that ther is no one below before starting to work.
4.
Always wear eye and ear protection when you
work.
5.
Always install the driver bit securely. A loose bit is
dangerous because it can come loose while you
are working. (WH18DSDL)
6.
Always use the driver bit that matches the screw
size. (WH18DSDL)
7.
Always have the screw you are screwing in and
this impact driver in a straight line. Working with
this impact driver at an angle to the screw can
damage the screw head and will not give the
prescribed tightening torque. (WH18DSDL)
8.
Confirm whether the socket has any crack in it.
(WR18DSDL)
9.
Attach the hex. socket securely onto the anvil. If
the hex. socket is insufficiently secured, it may drop
out and cause an accident. For hex. socket
attachment refer to "OPERATION". (WR18DSDL)
10. Confirm the tightening torque by a torque wrench
before use in order to ascertain the correct
tightening torque to be used. (WR18DSDL)
11. If a universal joint is used, be sure not to operate
the unit in a no-load condition. Operating in this
condition is dangerous. When the socket section
spins around it may cause injury to hands or
bodies, or the resulting intense vibration may
cause the user to drop the tool. (WR18DSDL)
12. Be careful that foreign matters do not block the
holes located on both sides of the handle. Also do
not close the holes with a tape. The holes act an
important role. (WR18DSDL)
AC Input Rating Amperes*
Equal to or
greater than
0
2
3
6
Table 1
RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
but less
than
2
3
4
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER
WARNING:
Death or serious bodily injury could result from
improper or unsafe use of battery chargers. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and
operating instructions for battery charger Model
UC18YRSL/UC18YFSL.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger,
(2) battery, and (3) product using battery.
3. To reduce risk of injury, charge HITACHI
rechargeable battery type BSL18 series. Other type
of batteries may burst causing personal injury and
damage.
4.
Do not expose battery charger to rain or snow.
5.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result in
a risk of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a.
That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b.
That extension cord is properly wired and in
good electrical condition; and
c.
That wire size is large enough for AC ampere
rating of battery charger as specified in
Table 1.
AWG Size of Cord
Length of Cord, Feet (Meter)
25 (7.5)
50 (15)
18
18
18
18
18
18
100 (30)
150 (45)
18
16
16
14
16
14
Publicidad
Tabla de contenido
