Troubleshooting; Specifications - Pioneer M-10X Manual De Instrucciones

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate
the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising
the checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair
work.
Symptom
No power is supplied
to unit.
No sound.
Abnormal functioning of this unit may be caused by static electricity, or other external interference. To restore
normal operation, turn the power off and then on again, or unplug the AC power cord and then plug it in again.

SPECIFICATIONS

Amplifier Section
Continuous power output
(both channels driven at 20 Hz to 20 kHz)*
T.H.D. 0.09 %, 4 Ω .............................. 90 W + 90 W
T.H.D. 0.05 %, 8 Ω .............................. 60 W + 60 W
DIN Continuous power output (both channels driven at
1 kHz)
T.H.D. 1.0 %, 4 Ω ............................ 120 W + 120 W
T.H.D. 1.0 %, 8 Ω ................................ 75 W + 75 W
Total harmonic distortion*
20 Hz to 20 kHz, 8 Ω ..................................... 0.05 %
• Power output specification is for when power sup-
ply is 230V.
Input sensitivity/ impedance ................ 700 mV/ 50 kΩ
Frequency response .................. 5 Hz to 100 kHz
Signal-to-Noise ratio (IHF A network, short circuit)
....................................................................... 118 dB
8
En/Ge
Cause
• Power plug is disconnected from inlet and outlet.
• The amplifier's power plug has been plugged
into another component's power outlet (e.g.
timer, etc.) but power to that unit is discon-
nected.
• STANDBY/ON button is set to STANDBY.
• MAIN POWER( —OFF/_ON ) button is set to
OFF.
• Connecting cords are disconnected from
terminals.
• Cords are connected incorrectly.
• Terminals or connecting cords pin plugs are
dirty.
• Operation of other components is incorrect.
For example:
In an A/V receiver the speaker settings are
incorrect, the input selector is set incorrectly,
the output settings are incorrect, or the
volume is turned all the way down.
In a DVD player the sound settings are in-
correct, etc.
• The disc you are using has no sound on these
channels.
+0
Power Supply/ Miscellaneous
Power requirements ..... AC 220 – 230 Volts, 50/ 60 Hz
Power consumption ............................................ 220 W
Power Consumption in standby mode .................. 1 W
Dimensions ................ 420 (W) × 319 (D) × 128 (H) mm
(including knobs and other protruding parts)
Weight (without package) ................................... 7.6 kg
Accessories
Operating instructions ................................................. 1
Power cord (Rated current 2.5 A) ................................ 1
Remote control cord .................................................... 1
Warranty card ............................................................... 1
NOTE:
Specifications and design subject to possible modification without
dB
notice, due to improvements.
–3
* Measured by Audio Spectrum Analyzer.
Remedy
• Insert plug securely into inlet and
outlet.
• Turn on power to other compo-
nent.
• Press the STANDBY/ON button
to ON so that the STANDBY
indicator goes off.
• Set the MAIN POWER (—OFF/
_ON ) button to ON.
• Connect securely.
• Connect correctly. (See page 5)
• Clean terminals and plugs.
• Consult the operating instructions
for the other components.
• Check the format of the disc you
are using.
Published by Pioneer Corporation.
Copyright © 2000 Pioneer Corporation.
All rights reserved.