Customising The Input Settings; Using Electronic Programme Guide - OK. OLE 396 B-D4 Manual De Usuario

Assigning a channel decoder
Decoders that decode analogue channels can be
connected to the AV connector. Assign the TV
channel as a channel to be decoded. Then assign
the connection where the decoder is connected.
1. Press Menu on the remote control and select
Setup > Decode.
2. Press OK/► to enter the list.
3. Press ▲/▼ to select the channel to decode.
4. Press OK to select or unselect the channel.
5. Press Menu to return to the previous menu.
Diagnostics on digital TV channels
1. Press Menu on the remote control and select
Setup > Diagnostics.
2. Press OK/► to display some signal information
on the current digital channel, such as signal
strength, frequency, etc.
Time shift
Allows you to time shift non-encrypted TV
programmers so that you will not miss the
favourite part even if you go out. Before you use
the function, connect a USB device to the TV first.
For the first time, you should do the disk setup
for the USB device.
Note: Feature is available only in selected
products and due to specific TV network
limitations and country technical
requirements might not be available in
product or place of installation. Feature
might be also blocked by TV network
due to copyright protection (HD content,
recording protection). Please use Option
on the remote control to check if feature is
available in your product.
1. Press Menu on the remote control and select
Setup > Time shift.
2. Press ◄/► to select On to switch on the time
shift function, then press Exit to close the
menu.
3. Press Option on the remote control and select
Time shift, then press OK to confirm.
4. Follow the directions on the screen to do the
setup.
5. After the disk setup is done, press Option and
select Time shift.
6. Press OK to display the time shift menu.
- Press the red button to pause the picture and
begin the time shift.
- Press the red button to play the recorded
part.
- When the time shift menu disappears and
only the timing of the time shift remains on
the screen, you can press the red button or
OK to access the time shift menu.
- Press the green button to fast backward or
the yellow button to fast forward.
- Press the blue button to quit the time shift
function.
Notes:
- Before you connect the USB device to the TV,
make sure you have backed up the data in
the device to avoid the loss of your important
data due to unforeseen malfunction.
- We recommend you use a USB device with
free capacity above 1GB and disk speed
faster than 5.0MB/sec.
- The bigger the file size for time shift, the
longer the recording time.
- If you change the channel in time shift mode,
a message prompts you to select Yes or
No. You can select Yes to exit the time shift
function and execute the channel change.
Reset shop
Allows you to reset the TV to factory default
settings.
1. Press Menu on the remote control and select
Setup, then press OK to confirm.
2. Select Reset shop and press OK/► to enter.
3. Use the
numeric
password.
4. Press ◄/► to select OK and press OK to
confirm.
5. The Initial setup menu appears. Follow the
related instructions.

Customising the input settings

You can configure your TV according to the
equipment you connect to it.
1. Press Menu on the remote control and select
Setup > Input settings.
2. Press OK/► to enter Input settings.
3. Press ▲/▼ to select a connector your
equipment is connected to.
4. Press ◄/► to select the type of apparatus
attached to this connector.
5. Press Menu to return to the Setup menu.
After configuring, the selected source label will be
displayed after the name of the related connector
in the source list when pressing Source on the
remote control or OK on the TV set.
Note: Not all models have OK button on the set.

Using Electronic programme guide

EPG is an on-screen guide that displays scheduled
TV programmes. You can navigate, select, view
and record programmes.
1. Press Guide on the remote control, the Now
and Next EPG menu will appear, which allows
you to get information about the current or next
programme playing on each channel. Navigate
through the different programmes using the
navigation buttons on the remote control.
EN 13
Using more of your TV
buttons to enter the