Numark MIXTRACK PRO Guia De Inicio Rapido página 5

18. CUE – The CUE button will return and pause the track at the last set cue point. For temporary play of
the cue point, you can hold down the CUE button. The track will play for as long as the button is held
down and will return to the cue point once it has been released.
You can hold down CUE and PLAY / PAUSE simultaneously to start playback from the cue point.
Release both buttons to allow playback to continue.
19. SYNC – Automatically matches the corresponding Deck's tempo with the other Deck's tempo.
20. PITCH FADER – Controls the track's playback speed. An LED next to the fader will light up when set
at 0%.
21. PITCH BEND ( + / – ) – Press or hold down either of these buttons to temporarily adjust the track's
playback speed. When released, the track playback will return to the speed designated by the PITCH
FADER.
22. KEYLOCK – This feature allows you to change the speed of the song without changing the key. The
key of the song will lock to the position of the pitch fader when Keylock is engaged.
23. HOT CUE BUTTONS (1-3) – Assigns a Cue Point or returns the track to that Cue Point. When a HOT
CUE BUTTON is unlit, you can assign a Cue Point by pressing it at the desired point in your track.
Once it is assigned, the HOT CUE BUTTON will light. To return to that Cue Point, simply press it.
24. DELETE – Press this to enable Delete Cue Mode, so you can erase assigned Cue Points from the
HOT CUE BUTTONS. When the DELETE button is lit, it is in Delete Cue Mode. You can then press a
red HOT CUE BUTTON to delete its assigned Cue Point.
25. EFFECT ON / OFF – Press this button to activate or deactivate the effect. The button's LED will
illuminate when the effect is on.
26. EFFECT SELECT – Turn this knob to select an effect to apply to the channel, which will be displayed in
the software. You can also press the knob to move automatically to the next effect.
27. EFFECT CONTROL – Turn this knob to adjust the parameter of the effect, which will be displayed in
the software.
28. MODE – Press this to switch between Manual Mode and Autoloop Mode, which changes the functions
of the LOOP CONTROL buttons.
Manual Mode:
• IN – Press this to set a "Loop In" point where your loop will begin.
• OUT – Press this to set a "Loop Out" point where your loop will end.
• RELOOP – Press this to jump to the start of the loop and enable it. If the Deck is already looping
when you press it, the Audio Pointer will jump to the start of the loop and continue. (If no loop is
set, nothing will happen.)
Autoloop Mode:
• 1/2 X – Press this to halve the length of the loop.
• 1 BAR – Press this to set a 1-bar loop automatically and enable it.
• 2 X – Press this to double the length of the loop.
29. OUTPUT 1 (RCA) – This stereo RCA connection will output the Master Mix from your computer.
Please use a stereo RCA cable to connect this output to a powered speaker or amplifier system.
30. OUTPUT 2 (RCA) – This stereo RCA connection will output the Cue Channel from your computer for
monitoring purposes. Please note that the Cue Channel is also output through the HEADPHONES
output on the front panel.
Note: If you are using Virtual DJ Pro, you may assign the Cue Channel to OUTPUT 2 or split the left
and right channels of the Master Mix to OUTPUT 1 and OUTPUT 2, respectively.
31. HEADPHONES – This stereo 1/4" output will output the signal being routed to the Cue Channel.
32. MIC GAIN – This knob controls the microphone level being sent to the Master Mix.
33. MIC THROUGH – This is a 1/4" microphone input. The signal from this input will be sent directly to the
Master Mix.
3