Releasing The Cutting-Means Assembly; Cutting Height Adjustment; Support Arm Release Levers; Quick Flip" Release Levers - Stiga 110 Combi Pro EL QF Manual De Uso

4.2.5 Assembling the canvas guard
1. Insert the two coupling hooks (fig. 11.A),
found at the ends of the support chassis
(fig. 11.B) inside the guide pins (fig. 11.C).
2. Position the support chassis (fig. 12.A)
under the device (fig. 12.B), and fasten
in place with the two screws (fig. 12.C).
4.2.6 Coupling to the accessory
lifting device
The cutting-means assembly is coupled
to the accessory lifting lever (fig. 13.A) of
the main machine by means of a spring
and chain and a snap-on hook.
The snap-on hook (fig. 13.B) is used for the
working position and can be moved between
the chain links to adjust the lifting force.
4.2.7 Connecting the power
cable connector
Connect the connector (fig. 14.B)
to the socket (fig. 14.A).
4.3 RELEASING THE CUTTING-
MEANS ASSEMBLY FROM
THE RIDE-ON MOWER
To release it correctly, follow the
steps below in the same order.
1. Disconnect the machine cable (fig. 14.B).
2. Disconnect the chain from the "accessory
lifting lever" (fig. 13.A) releasing
the snap-on hook (fig. 13.B).
3. Remove the canvas guard by
undoing the screws (fig. 12.C)
4. Disconnect the plug or split pin (fig. 8.D)
and rotate the quick release supports
to the open position (fig. 7.A).
5. Loosen and release the
transmission belt as follows:
• 4WD models
– Use the left hand to grasp the tensioner
lever (fig.9.A) and pull it outwards.
– Use the right hand to remove the
belt from the pulley (fig. 9.C).
– Extract the belt from the
machine pulley (fig. 9.B).
• 2WD model
– Use the left hand to grasp the tensioner
lever (fig. 10.A) and pull it outwards.
– Use the right hand to remove the
belt from the pulley (fig. 10.C).
– Extract the belt from the
machine pulley (fig. 10.B).
6. Raise the quick release support coupling
brackets (fig. 7.B) and separate the
cutting-means assembly from the
ride-on mower with front deck.
5. CONTROLS

5.1 CUTTING HEIGHT ADJUSTMENT

Always perform adjustments when
the cutting means are stationary.
5.1.1 Electric cutting height adjustment
The cutting height is adjusted in
infinitesimal mode, enabling the electric
cutting height adjuster switch found
on the front deck ride-on mower.
The cutting height indicator (fig. 1.l)
shows the adjusted height.
IMPORTANT To enable the electric adjustment
it is necessary to connect the cutting-means
assembly electric cable connector to the socket
(fig. 14.A) found on the front deck ride-on mower.

5.2 SUPPORT ARM RELEASE LEVERS

The support arm release levers (fig. 1.G) are used
to release the rear section of the cutting-means
assembly from the support arms and lower it.
From this position it is possible to lift the
cutting-means assembly to the maintenance
and wash position (chap. 7.2);

5.3 "QUICK FLIP" RELEASE LEVERS

The "Quick Flip" release levers make it possible
to quickly lower the cutting-means assembly to
the maintenance and wash position (chap. 7.2);

6. USING THE MACHINE

IMPORTANT The safety regulations to
follow during machine use are described
in chapter 2. Strictly comply with these
indications to avoid serious risks or dangers.

6.1 PRELIMINARY PROCEDURES

It is possible to cut the grass using
two different operating modes:
EN - 6