Assembly Prior To Installation - Jotul F 100 Manual De Uso

ENGLISH
3.4 Chimneys and flue pipes
• A chimney can be linked to the fireplace and flue approved
for solid fuel-fired fireplaces with a flue gas temperature as
specified in «2.0 Technical data».
• The cross-section of the chimney must be at least equal to
the cross-section of the flue. Please use «2.0 Technical data»
to calculate the correct cross-section of the chimney.
• Several solid fuel-fired fireplaces can be connected to the
same chimney if the cross-section of the chimney is adequate.
• Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.
• Before making a hole in the chimney the fireplace should be
test-mounted in order to correctly mark the position of the
fireplace and the hole in the chimney. See fig. 1 for minimum
dimensions.
• Ensure that the flue pipe is inclined all the way up to the
chimney.
• Use a flue pipe bend with a sweeping hatch that allows it
to be swept.
Be aware of the fact that connections must have a certain
flexibility in order to prevent movement in the installation
leading to cracks. N.B. A correct and sealed connection is very
important for the proper functioning of the product.
The chimney draught, see «2.0 Technical data». If the draught is
too strong you can install and operate a flue damper to control
the draught.

3.5 Assembly prior to installation

N.B. Check that the fireplace is free of any damage prior to
commencing installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fireplace.
1. The product is delivered in a single packing case where the
smoke outlet, ash lip and door bolt knob must be assembled.
2. Once you have unpacked the product, remove all loose parts.
Check that the product does not have any visible damage and
that the operating handles work.
Rear mounted flue pipe
If the flue pipe is to be rear mounted do the following:
• Cut out a hole in the heat shield at the back for the
flue pipe (fig. 3).
• Unscrew the two screws holding the cover for the rear
outlet from the inside. (Hold the cover when removing
the last screw) (fig. 5A).
• Fasten the cover on the top plate.
• Connect the smoke outlet to the rear plate.
• Install the ash lip by hanging it under the door.
• Screw the door knob on the handle. (Place the white
washer between the handle and the knob.)
• Remove the protective paper from the gasket and
fasten it around the outside of the flue pipe.
• Mount the flue pipe into the flue outlet.
N.B. It is important that the joints/flue pipes are completely
sealed. Air leaks can prevent the flue pipe from functioning
properly.
18
Top mounted flue pipe
If the flue pipe is to be top mounted do the following:
1. Attach the flue outlet to the top plate using the two screws.
Fig. 4A.
2. Install the ash lip by hanging it under the door.
3. Screw the door knob on the handle. (Place the white washer
between the handle and the knob.)
4. Remove the protective paper from the gasket and fasten it
around the outside of the flue pipe.
5. Mount the flue pipe into the flue outlet.
N.B. It is important that the joints/flue pipes are completely
sealed. Air leaks can prevent the flue pipe from functioning
properly.
3.6 Control of functions
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 100 is equipped with the following controls:
fig. 2A
Air vent:
fig. 2B
Ignition vent:
To the left: Closed
To the right: Open
3.7 Ash removal (fig 6)
Jøtul F 100 with ash pan
1. Open the grate.
2. Lift out the ash pan.
3. Carefully place the grate down.
4. Ideally, some ash should be left as a protective layer for the
bottom of the fireplace.
5. Make sure the door to the ash pan is securely shut when the
stove is in use.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».
Jøtul F 100 without ash solution
1. Lift out the ash retainer
2. Use a shovel or similar and scrape out the ash.
3. Leave a little ash in the bottom of the combustion chamber
as a protective insulating layer.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».
«6.1 Fire preventive
«6.1 Fire preventive