Important Hints; Symbols; Unpacking; Positioning The Instrument - Hameg Instruments HM5510 Manual

I m p o r t a n t h i n t s

Important hints

Symbols

(1) (2) (3)
Symbol 1: Attention, please consult manual
Symbol 2: Danger! High voltage!
Symbol 3: Ground connection
Symbol 4: Important note
Symbol 5: Hints for application
Symbol 6: Stop! Possible instrument damage!

Unpacking

Please check for completeness of parts while unpacking. Also
check for any mechanical damage or loose parts. In case of
transport damage inform the supplier immediately and do not
operate the instrument.
Check setting of line voltage selector whether it corresponds
to the actual line voltage.

Positioning the instrument

As can be seen from the fi gures, the handle can be set into
different positions:
A and B = carrying
C = horizontal operating
D and E = operating at different angles
F = handle removal
T = shipping (handle unlocked)
Attention!
When changing the handle position, the instru-
ment must be placed so that it can not fall (e.g.
placed on a table). Then the handle locking knobs
must be simultaneously pulled outwards and
rotated to the required position. Without pulling
the locking knobs they will latch in into the next
locking position.
Handle mounting/dismounting
The handle can be removed by pulling it out further, depending
on the instrument model in position B or F.

Transport

Please keep the carton in case the instrument may require
later shipment for repair. Improper packaging may void the
warranty!

Storage

Dry indoors storage is required. After exposure to extreme
temperatures 2 h should be allowed before the instrument
is turned on.
26
Subject to change without notice
STOP
HINT
(4) (5) (6)
B
C
T
A
F
D
E
A

Safety guidelines

This instrument was manufactured and tested in accordance
with VDE 0411, part 1, „Safety Rules for Electric Measuring and
Control Laboratory Instruments", it left the factory in proper
safe condition. It conforms hence also with the European
standard EN 61010-1 resp. the international standard IEC
61010-1. In order to keep this condition up and to guarantee safe
operation the user is requested to observe the warning hints
as well as the other hints carefully which are contained in this
manual. Housing, chassis, and all measuring connections are
connected to the mains safety earth. The instrument conforms
to the rules for Protective Class I. All metal parts which can be
touched were tested against the mains with 2200 V DC.
Safety rules require that this instrument may only be operated
from a mains outlet which conforms to the respective safety
standards. The mains plug must be inserted fi rst before any
signals may be connected to the instrument.
In case there are doubts about the conformity of a mains
outlet the outlet must be tested according to DIN VDE 0100,
part 610.
B
C
PUOPFGkT PUOPFGkT PUOPFGkT
PUOGkT PUOPFGkT PUOPFGkT PUOPFGkT
HM507
PUOPFGkT PUOPFGkT
PUOPFGkT PUOPFGkT PUOPFGkT PUOPFGkT
PUOPFGkT PUOPFGkT PUOPFGkT
PUk PUk PUk PUk PUk PUk
B PUkT
HGOPFFD
PUOPFGkT
PUOPFGkT
PUkT
PUkT HGOFFD PUkT PUOPFGkT PUOPFGkT
PUkT PUkT PUkT
INPUT CHI PUkT INPUT CHI HAMEG INPUT CHI
OPK OPK OPK
HJ PUkT HJ HJ
VBN PUOPFGkT VBN VBN
HJKL HJKL PUOPFGkT HJKL
T
T
D
E