Publicidad
Idiomas disponibles
Idiomas disponibles
3. take off the seat cushion to facilitate the installation.
4. pass the abdominal strap of the seat belt through the lower
seat guides
(K)
(fig.3.3) and buckle the vehicle seat belt until
you hear a click (fig. 3.4).
5. pass the diagonal section of the seat belt through the
corresponding upper guide
6. take up the remaining slack of the diagonal section of the 3-point
seat belt (fig. 3.6). and make sure it is as tight fitting as possible.
Ensure the straps are not twisted or knotted at any point.
7. place the seat cushion on the seat.
4. PlacIng the chIld In the seat. grouP 0+
Proper adjustment of the height of the harness ensures the child
will be seated correctly. The harness should be adjusted to the
height of the child's shoulder or slightly above; never behind the
child's back or level with the ears (fig. 4.1).
1. loosen the harness straps
pressing the harness adjustment button
2. release the buckle
(f)
to make it easier to seat the child (fig.
4.3).
3. place the child in the seat.
4. Secure the child in the harness by joining the two parts
of the clasp and fastening the buckle
click (fig. 4.4).
5. Gently pull the harness adjustment strap to achieve the correct
tension
(g)
(fig. 4.5). Remember that in order to ensure the
child's safety the harnesses should fit tightly.
5. adJustIng the headrest heIght
Proper adjustment of the height of the headrest ensures the child
will be seated correctly. The headrest should be adjusted to
ensure that the harness straps
of the child's shoulder or slightly above; never behind the child's
back or level with the ears (fig. 4.1).
22
(Q)
as shown (fig. 3.6).
(e)
by pulling them gently while
(J)
(fig. 4.2).
(f)
until you hear a
(e)
should be adjusted to the height
1. loosen the harness straps
(e)
pressing the harness adjustment button
2. Adjust the headrest according to the child´s height by pulling the
headrest height regulator
(a)
the child´s shoulder or slightly above (fig. 5.2).
6. InstallIng the car seat. grouP 1
grouP 1 only. from 9 months to 4 years
notIce
approx. (9-18 kg)
1. Ensure the seat is not in a reclined position (the indicator should
be in position 1) and is ready to install in forward position
(Group 1) as shown fig. 6.1. pull the lever
adjust the angle of recline to position 4 without releasing the lever.
Release the lever when the seat is in the desired position (fig. 6.1)
2. Pull the ISOFIX adjuster
(I)
to extract both arms (m). Move the
locking arms from side to side until you hear the click indicating
that they are fully locked (fig. 6.2).
3. take the top tether and pass it over the seat.
4. place the child safety seat in the back seat of the vehicle facing
in the direction of travel.
5. hold the safety seat with both hands and insert the two locking
arms
(m)
into the verhicle´s Isofix connectors until they fasten with
a click on both sides. the red button will change to green on both
sides (fig. 6.3).
7. shake the seat to check that it is correctly anchored to the vehicle's
ISOFIX points.
ImPortant! the locking arms are only correctly fixed if both safety
buttons are green.
8. Pull the ISOFIX adjuster and push the safety seat towards the back
using a firm, constant pressure on both sides until it rests firmly
against the vehicle seat (fig. 6.4). If necessary, adjust the reclining of
the vehicle´s seat backrest to ensure that the child seat rests correctly.
by pulling them gently while
(J)
(fig. 5.1).
adjusting the harness to the height of
(h)
forward and
23
Publicidad
