Pioneer DJM-2000 Manual De Instrucciones página 23

REV ROLL
1 2
Original
Effect turned on
1/1 reverse
roll
Reversed and repeated
This function records the input sound at the point at which the [ON/ OFF] but-
ton is pressed, reverses the recorded sound and repeats it according to the beat
button's fraction.
The effect time is set from 1/8 to 4/1 with respect to 1 beat of
Beat buttons (parameter 1)
BPM time.
Use this to set the effect time.
TIME (parameter 2)
10 to 4000 (ms)
LEVEL/ DEPTH (param- Use this to set the balance between the original sound and
eter 3) ROLL.
Use these to set the balance between the original sound and
EFFECT FREQUENCY
(parameter 4) the ROLL for the different bands.
FILTER
1
This function changes the filter's cut-off frequency according to the beat button's
fraction.
These set the cycle for moving the cut-off frequency from 1/8 to
Beat buttons (parameter 1)
4/1 with respect to 1 beat of BPM time.
Use this to set the cycle at which the cut-off frequency is
TIME (parameter 2) moved.
10 to 32000 (ms)
LEVEL/ DEPTH (param- The further the control is turned clockwise, the more the effect
eter 3) is stressed.
EFFECT FREQUENCY These set the balance between the original sound and the
(parameter 4) effect sound for the different bands.
TRANS
1
MIN MAX
1/1 beat
Cut
MIN MAX
Cut Cut
MIN MAX
EFFECT FREQUENCY
This function cuts the sound according to the beat button's fraction.
The amount of the sound to be cut can be changed at [EFFECT FREQUENCY].
These set the 1/8 to 4/1 cut time with respect to 1 beat of BPM
Beat buttons (parameter 1)
time.
Use this to set the effect time.
TIME (parameter 2)
10 to 16000 (ms)
LEVEL/ DEPTH (param- Sets the balance between the original sound and the effect
eter 3) sound.
EFFECT FREQUENCY This sets the amount of the original sound to be cut for the
(parameter 4) different bands.
PHASER
1
Phase shift
Cycle
The phaser effect changes according to the beat button fraction.
Frequency
Time
Cut
Time
These set the cycle for moving the phaser effect by 1/8 to 4/1
Beat buttons (parameter 1)
with respect to the time of one BPM beat.
This sets the cycle by which the phaser effect is moved.
TIME (parameter 2)
10 to 32000 (ms)
The further the control is turned clockwise, the more the effect
LEVEL/ DEPTH (param- is stressed.
eter 3) When turned all the way counterclockwise, only the original
sound is output.
EFFECT FREQUENCY Use these to set the balance between the original sound and
(parameter 4) the effect sound for the different bands.
GATE
1
Level
Threshold
MIN MAX
Threshold
MIN MAX
Threshold
MIN MAX
EFFECT FREQUENCY
This function outputs the input sound that has a level above the threshold level,
cutting the input sound that has a level below the threshold level.
The threshold level can be changed at [EFFECT FREQUENCY].
Beat buttons (parameter 1) This sets the release time between 1 and 100 %.
This sets the release time.
TIME (parameter 2)
1 to 100 (%)
Sets the threshold level.
LEVEL/ DEPTH (param-
The further the control is turned clockwise, the more the effect
eter 3)
is stressed and the sound is cut.
EFFECT FREQUENCY
Use these to set the threshold levels for the different bands.
(parameter 4)
SEND/RETURN
1
SEND
RETURN
DJM-2000
Connect an external effector, etc., here.
[EFFECT FREQUENCY] can be used as an isolator.
Beat buttons (parameter 1) —
TIME (parameter 2) —
LEVEL/ DEPTH (param-
This adjusts the sound level input to the [RETURN] terminal.
eter 3)
EFFECT FREQUENCY This sets the audio output level of the RETURN sound for the
(parameter 4) different bands.
1 When "A", "B" or "M" is selected with the [CH SELECT] buttons, the effect sound
cannot be monitored by pressing [CUE] (BEAT EFFECT) unless the sound for
the channel you want to monitor is being output from [MASTER] channel.
2 When BEAT EFFECT is off, the effect sound cannot be monitored by pressing
[CUE] (BEAT EFFECT).
Time
Effector
23
En