Poulan Pro PPBV25 Manual De Instrucciones página 4

hurt people or animals, break glass, or
cause other damage.
Never run unit without the proper equipment
D
attached. When using your unit as a blower,
always install blower tubes. When using your
unit as a vacuum, always install vacuum
tubes and vacuum bag assembly. Make sure
vacuum bag assembly is completely zipped.
Check air intake opening, blower tubes,
D
vacuum tubes, and elbow tube frequently,
always with engine stopped and spark plug
disconnected. Keep vents and discharge
tubes free of debris which can accumulate
and restrict proper air flow.
Never place any object in the air intake open-
D
ing as this could restrict proper air flow and
cause damage to the unit.
Never use for spreading chemicals, fertiliz-
D
ers, or other substances which may contain
toxic materials.
To avoid spreading fire, do not use near leaf
D
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
Use only for jobs explained in this manual.
D
MAINTAIN YOUR UNIT PROPERLY
WARNING:
fore performing maintenance except for carbu-
retor adjustments.
Have all maintenance other than the rec-
D
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
Use only recommended Poulan PRO re-
D
placement parts; use of any other parts
may void your warranty and cause damage
to your unit.
Empty fuel tank before storing the unit. Use
D
up fuel left in carburetor by starting engine and
letting it run until it stops.
WARNING:
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
WARNING:
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
A standard screwdriver is required for as-
D
sembly.
BLOWER TUBE ASSEMBLY
1. Align the rib on the upper blower tube with
the groove in the blower outlet; slide the
tube into place.
NOTE:
Bolt must be loose enough to allow
blower tube to be inserted in blower outlet. Loos-
en bolt by turning counterclockwise.
Disconnect spark plug be-
ASSEMBLY
Stop engine and be sure
If you receive your unit
Do not use any accessory or attachment
D
other than those recommended by manufac-
turer for use with your unit.
Do not store the unit or fuel in a closed area
D
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
Store in a dry area out of reach of children.
D
SPECIAL NOTICE:
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of peo-
ple prone to circulation disorders or abnormal
swelling. Prolonged use in cold weather has
been linked to blood vessel damage in other-
wise healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in skin
color or texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this tool
and seek medical attention. An antivibration
system does not guarantee the avoidance of
these problems. Users who operate power tools
on a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
Refer to the MAINTENANCE section for infor-
mation on maintenance of the muffler and spark
arresting screen.
2. Secure the tube by turning the bolt clock-
wise.
3. Align the slots on the lower blower tube
with the tabs on the upper blower tube.
Upper Blower Tube
-- 4 --
Exposure to vibrations
This unit is equipped
Tab
Lower Blower Tube
Slot