Operation; Function - Espa Evopool SilenPlus Manual De Instrucciones

4.4 In the absence of
If you do not have
the system can work just as well manually.
Ignore the activation and calibration operations, switch
to Manual mode and then connect the
4.5 Changing the
If it is necessary to replace the
system that is already linked, you will need to delete
the old serial number before linking the new one.
To do this, with the
power supply, keep the F button pressed down for 10
seconds. Flashing leds indicate that the operation has
been carried out correctly.
The previous serial number will be deleted and the
system will go into "link standby" mode. Proceed as
indicated in 4.2.2.

5. OPERATION

5.1 REMOTE mode
This is the default operating mode.
The pump carries out the most appropriate function con-
sidering the position of the filter valve. (See figure 3)
In FILTRATION position:
In BACKWASH position:
In CLOSED position: pump stopped.
In any of the other positions: the pump operates at
100% power.
When you operate the valve control, the pump
stops automatically to make the valve movement
easier.
In any intermediate position, the pump remains
stopped.
To change the working mode, simply move the valve
to the desired position.
To prevent accidental operation, the electronic
response is delayed by 1 second. The flashing
red LED indicates that proper communication
has been achieved.
Move the valve gently.
WARNING: the valve configuration must corre-
spond to the 6 standard positions, according to
figure 3.
For other valve configurations, contact your technical
service.
5.2 MANUAL mode
When you press the M key,
signal and runs one of the pre-set functions:
The MAN LED comes on.
The pump starts up at a fixed, programmable speed.
The standard setting is 2,300 RPM (40 Hz). This is
what is known as the MIXED CYCLE (MISC. CYCLE).
If you press the F key, it runs through the various
functions in sequence.
Between each function, the pump stops to allow valve
movement or other operations.
or prefer not to use it,
.
in a
pump connected to the

function

function
ignores the
The sequence is:
1. Mixed cycle (MISC. CYCLE).
2. Stop.
3. .
4. Stop.
5.
6. Stop.
7. Mixed cycle...
The lit leds indicates the function selected at all times.
When you press the M button again, you leave Manu-
al mode to go back to Remote.
5.3 No water fault and retries.
In mode, the system is regularly moni-
tored to check that the pump is not operating without
water.
If detects the pump is working without water
it stops the motor.
The system will attempt to start up again after 1', 5',
15' and 1 hour (Fig. 4). If the retries fail,
remain in permanent fault mode.
An LED sequence indicates the fault status. (See fig-
ure 7)
To interrupt the retry cycle or to restart from perma-
nent fault mode, press the F key.
5.4 System status
Espa offers installers and users the
plication for monitoring the system status and
interacting with
They must have a Smartphone with Bluetooth
connectivity and
available in
PlayStore or AppStore.
With this app, it is possible to switch between Manu-
al/Remote modes and use all functions.
FUNCTION
6.
6.1 Activation.
should only be activated after carrying out
the initial maintenance work, making sure that the filter
is completely clean.
To activate
- Press "M" for 5 seconds.
- The " " LED will blink 3 times.
When it is activated,
learning period during which the pump will operate at
100%. Do not interrupt this process.
The correct activation of the
indicated by the
6.2 Auto-adaptation.
With activated, the pump operation during
the phase will adjust itself to the degree
of clogging of the filter.
It is normal to note a gradual increase in the rotational
speed of the pump.
11
EN
.
.
install the application
www.espa.com
will begin a 3 minute
function is
LED blinking slowly
will
ap-
and in