Starting And Operating Of The Machine; After Use - Gerni VAC 1320 Dry Instrucciones De Uso

NOTE! Before dry material pick-up - All models
Dry cleaner VAC 1320 Dry shall always have the sack
*
fi lter mounted in the machine.
* Wet cleaners shall always have the sack fi lter and the
fl oat system mounted when picking up dry material.
This is also valid when using a dust bag.
NOTE! Before wet pick-up - not for 1320 Dry
Never use dust bag or sack fi lter when performing wet pick-up. The
machine is equipped with a fl oat system that shuts off the airfl ow through
the machine when the maximum liquid level is reached. Never pick up
liquid without the fl oat body in place.
To control: Loosen the two latches at each side of the motor top. Then
remove the motor top. Check that the fl oat basket and fl oat valve are
mounted at the motor top. See chapter 4 for mounting the fl oat system.
Remounting the motor top: Put back the motor top to the container.
Make sure that the switch/switches is located in direction towards the
suction inlet. Then tighten both latches so that the motor top is properly
secured. Always use a chemical defoamer when picking up water
containing foaming detergents. Use a defoamer recommended by the
detergent manufacturer.

1 Starting and operating of the machine

Check that the electrical switch is switched off (in position 0). Then connect
the suction hose into the suction inlet at the machine by pushing the hose
forward until it snaps in place at the inlet (to release the hose from mach-
ine just push the release button downwards and then pull out the hose).
Then connect the two tubes with the hose handle, twist the tubes in order
to ensure that they are properly fi tted. Attach suitable nozzle to the tube.
Choose nozzle depending on what type of material that is to be picked-up.
Connect the plug into a proper electrical outlet. Put the electrical switch
into position 1 in order to start the motor. Some variants have two motors/
fan units and two electrical switches - one switch for each motor.
1350, 1375 & 2750, 2775 Adjusting the handle
The handle can be adjusted to the suitable working heigth. Start by
loosing the two locking screws at each side of the handle. Then adjust the
handle by moving it upwards or downwards until the proper angle is found.
Tighten the both locking screws again to secure the handle.
Wet pick up NOTE! - Not for model 1320 Dry
The machine is equipped with a fl oat body that shuts of the airfl ow through
the machine when the maximum liquid level is reached. You will then hear
a noticeable change of the sound from the motor and notice that the suc-
tion power decreases. When this occurs, switch the machine of. Discon-
nect the machine from the socket. See chapter number 2 for emptying
after wet pick-up.
VAC TOOL1335 - Craftsman versions
These variants have an extra electrical outlet for connecting an drilling
machine or other electrical tools. Max 2000W power consumption is al-
lowed at the electrical tool to be connected. Your cleaner can then be used
to pick up wooden drillings and similair materials. The electrical outlet is
placed under a plastic cover at the front side of the motor top. The electri-
cal switch have two different positions.
Position I: Normal operation. The machine will be shut off when the switch
is placed in position 0.
Position II: craftsman operation. The extra electrical outlet is activated
in this position. The vacuum cleaner is now started by fi rst connecting an
electrical tool to the electrical outlet and then starting the electrical tool.
When the electrical tool is shut off the vacuum cleaner has 10 seconds
delayed shut off. The meaning of the delay is to ensure that the cleaner
has time to pick-up the material.
Bedienungsanleitung auf www.gluesing.net
823 0062 060 Instruction for use Gerni WEU.indd 7
INSTRUCTIONS FOR USE
2 Emptying after wet pick-up
Before emptying the container, unplug the vacuum cleaner. Always
empty and clean the container and the fl oat system after picking-up
liquids. Never pick up liquid without the fl oat system installed in the
machine.
Emptying 1320 Wet&Dry and 1335, 1335 VACTOOL
2a) Release the latch by pulling the lower parts outwards so that the motor
top is released. Lift up the motor top.
2b) Disconnect the hose from the inlet by pressing the button on the hose
connection downwards. Then pull out the hose.
2c) Empty by tilting the container backwards and pour the liquids into a
fl oor drain or similar.
2d) Wipe the fl oat valve and the fl oat basket with a damp cloth.
2e) Put back the motor top to the container. Make sure that the switch/
switches is located in direction towards the suction inlet. Secure with the
latches.
Emptying: 1350, 1375 & 2750, 2775 Wet&Dry
2f) Drain hose: 1375 and 2775 have a draining hose. Detach the drain
hose from the bracket by pulling hose backwards from the cleaner. Place
the drain hose end near a fl oor drain and then remove the plug at hose
end. The natural pressure will then drain the liquids from the container.
2g) Emptying from the container: Pull the upper parts of the latches out-
wards and release the motor top. Remove the motor top. The suction hose
can be attached during emptying from the container. Grasp with one hand
at the handle at the lower part of the container. To avoid movement of the
trolley - place one foot at the basepart of the trolley. Then tilt the container
backwards and pour the liquids into a fl oor drain or similar.
2h) Wipe the fl oat valve and the fl oat basket with a damp cloth.
2i) Put back the motor top to the container. Make sure that the switch/
switches is located in direction towards the suction inlet. Secure with the
latches.
3 Emptying after dry pick-up
Remove the plug from the socket before emptying after dry pick-up.
Check the sackfi lter or dustbag regularly. Release the latches by pulling
them outwards so that the motor top is released. Lift up the motor top from
container.
Sackfi lter:Grasp the sackfi lter and lift it up from cleaner. Shake fi lter so
that all dust is removed from the fi lter.
Dustbag: check bag to ensure the fi ll factor. Replace dust bag if neces-
sary. Remove the old bag. The new bag is fi tted by passing the carboard
piece with the rubber membrane through the
vacuum inlet. Make sure that the rubber membrane is passing past the
heightening at the vacuum inlet.
After emptying: Put back the motor top to the container. Make sure that
the switch/switches is located in direction towards the suction inlet. Secure
with the latches. Never pick up dry material without sackfi lter or dustbag fi t-
ted in the machine. The suction effi ciency of the vacuum cleaner depends
on the size and quality of the fi lter and dust bag. Therefore - use only
Original fi lter and dust bags.
4 Maintenance of the fl oat system
Remove the plug from the socket before performing maintenance.
Always empty and clean the container and the fl oat system after
picking-up liquids.
4a) Release the latch by pulling them outwards so that the motor top is
released. Lift up motor top from container. Turn the motor top to upside
down position.
4b)Then loosen the fl oat basket by turning the basket to the left. Remove
the complete fl oat system from motor top.
4c) A fi lter is located in front of the motor inlet. Check this motor fi lter and
HEPA-fi lter (if fi tted). Replace to new fi lter if fi lter is clogged.
4d) Wipe the fl oat valve and fl oat basket with a damp cloth before the
motor top is reinstalled to the container. Then reinstall the fl oat valve to
the fl oat basket. Make sure that the sealed surface of the fl oat valve is
installed upwards in direction towards the motor top.
4e) To mount the fl oat basket - fi t the arrow at the basket to the arrow at
the motor top. Then secure the fl oat basket by turning it to the right.

5 After use

Remove the plug from the socket when machine is not in use. Wind up the
cord starting from the machine. The power cord can be wound up around
the handle/hooks located on the motor top. Some variants have special
storage places for accessories.
7
2008-01-22 14:07:12