Makita DUR365U Manual De Instrucciones página 14

Power switch action
WARNING:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released. Operating a tool with a
switch that does not actuate properly can lead to loss
of control and serious personal injury.
Press and hold the main power button for some seconds
to turn on the tool. (Fig. 8)
To turn off the tool, press and hold the main power button
again.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided.
To start the tool, grasp the right grip (the lock-off lever is
released by the grasp) and then pull the switch trigger. To
stop the tool, release the switch trigger. (Fig. 9)
NOTE:
• The tool is automatically turned off after the tool is left
one minute without any operations.
Speed adjusting (Fig. 10)
You can adjust the tool speed by tapping the main power
button.
Each time you tap the main power button, one of the
speed indicator lights up in order of Turtle (
Rabbit ( ).
is for low speed and
indicator for middle speed.
Reverse button for debris removal
WARNING:
• Switch off the tool and remove the battery cartridge
before you remove entangled weeds or debris
which the reverse rotation function can not
remove. Failure to switch off and remove the battery
cartridge may result in serious personal injury from
accidental start-up.
This tool has a reverse button to change the direction of
rotation. It is only for removing weeds and debris
entangled in the tool. (Fig. 11)
To reverse the rotation, tap the reverse button and pull the
trigger when the tool's head is stopped. The power lamp
starts blinking, and the tool's head rotates in reverse
direction when you pull the switch trigger.
To return to regular rotation, release the trigger and wait
until the tool's head stops.
NOTE:
• During the reverse rotation, the tool operates only for a
short period of time and then automatically stops.
• Once the tool is stopped, the rotation returns to regular
direction when you start the tool again.
• If you tap the reverse button while the tool's head is still
rotating, the tool comes to stop and to be ready for
reverse rotation.
Nylon cutting head (optional accessory)
NOTICE:
• The bump feed will not operate properly if the head is
not rotating.
14
), middle,
for high speed, and the middle
The nylon cutting head is a dual string trimmer head
provided with a bump & feed mechanism.
To cause the nylon cord to feed out, the cutting head
should be bumped against the ground while rotating.
(Fig. 12)
NOTE:
If the nylon cord does not feed out while bumping the
head, rewind/replace the nylon cord by following the
procedures described under "Maintenance."
ASSEMBLY
WARNING:
• Always be sure that the tool is switched off and
battery cartridge is removed before carrying out
any work on the tool. Failure to switch off and remove
the battery cartridge may result in serious personal
injury from accidental start-up.
• Never start the tool unless it is completely
assembled. Operation of the tool in a partially
assembled state may result in serious personal injury
from accidental start-up.
Installing the handle
Insert the shaft of the handle into the grip. Align the screw
hole in the grip with the one in the shaft. Tighten the screw
securely. (Fig. 13)
Place handle between handle clamp and handle holder.
Adjust the handle to an angle that provides a comfortable
working position and then secure by firmly hand-
tightening knob. (Fig. 14)
Installing the guard
WARNING:
• Never use the tool without the guard illustrated in
place. Failure to do so can cause serious personal
injury.
• Always use the tool with the approved combination of
the safety equipments. Otherwise contact with a cutting
tool may cause serious injury.
• Permitted combination for the cutting tool and the
guard may differ from country to country. Follow your
region's regulations.
For metal blade (Fig. 15 & 16)
For nylon cutting head or plastic blade
CAUTION:
• Take care not to injure yourself on the cutter for cutting
the nylon cord when installing nylon cutting head or
plastic blade. (Fig. 17)
Align the clamp on the pipe with the protector. And tighten
them with bolts. (Fig. 18)
Installing the metal blade (optional
accessory)
WARNING:
• The outside diameter of the metal blade must be
230 mm. Never use any blade exceeding 230 mm in
outside diameter.