Hitachi C 8FC Instrucciones De Manejo página 6

Sierra compuesta
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 35
English
GENERAL OPERATIONAL PRECAUTIONS
WARNING!
When using power tools basic safety precautions should
always be followed to reduce the risk of fire, electric shock
and personal injury, including the following.
Read all these instructions before attempting to operate
this product and save these instructions.
1.
Keep work area clean. Cluttered areas and benches
invite injuries.
2.
Consider work area environment. Do not expose
power tools to rain. Do not use power tools in damp
or wet locations. Keep work area well lit.
Do not use tools in the presence of flammable liquids
or gases.
Power tools produce sparks during operation. They
also spark when switching ON/OFF. Never use power
tools in dangerous sites containing lacquer, paint,
benzine, thinner, gasoline, gases, adhesive agents,
and other materials which are combustible or
explosive.
3.
Guard against electric shock. Avoid body contact
with earthed or grounded surfaces. For example;
pipes, radiators, refrigerator enclosures.
4.
Keep other persons away. Do not let persons,
especially children, not involved in the work touch
the tool or the extension cord and keep them away
from the work area.
5.
Store idle tools. When not in use, tools should be
stored in a dry locked-up place, out of reach of
children.
6.
Do not force the tool. It will do the job better and
safer at the rate for which it was intended.
7.
Use the right tool. Do not force small tools to do the
job of a heavy duty tool. Do not use tools for
purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
8.
Dress properly. Do not wear loose clothing or
jewelry. They can be caught in moving parts. Non-
skid footwear is recommended when working
outdoors. Wear protective hair covering to contain
long hair.
9.
Use protective equipment. Use safety glasses. Use
face or dust mask if cutting operations create dust.
10. Connect dust extraction equipment.
If device are provided for the connection of dust
extraction and collecting equipment, ensure these
are connected and properly used.
11. Do not abuse the cord. Never yank the cord to
disconnect it from the receptacle. Keep the cord
away from heat, oil and sharp edges.
12. Secure work. Where possible use clamps or a vise
to hold the work. It is safer than using your hand.
13. Do not overreach. Keep proper footing and balance
at all times.
14. Maintain tools with care. Keep cutting tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing
accessories. Inspect tool cords periodically and if
damaged have them repaired by an authorized
service facility. Inspect extension cords periodically
and replace if damaged. Keep handles dry, clean and
free from oil and grease.
15. Disconnect tools. When not in use, before servicing
and when changing accessories such as blades, bits
and cutters, disconnect tools from the power supply.
16. Remove adjusting keys and wrenches. Form the
habit of checking to see that keys and adjusting
wrenches are removed from the tool before turning
it on.
17. Avoid unintentional starting. Do not carry plugged-
in tool with finger on switch. Ensure switch is in "off"
position when plugging in.
18. Use outdoor extension leads. When the tool is used
outdoors, use only extension cords intended for
outdoor use and so marked.
5
19. Stay alert. Watch what you are doing. Use common
sense. Do not operate the tool when you are tired.
20. Check damaged parts. Before further use of tool, it
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center unless otherwise indicated in this
handling instructions. Have defective switches
replaced by an authorized service center. Do not use
the tool if the switch does not turn it on and off.
21. Do not use power tools for applications other than
those specified in the handling instructions.
22. Warning
The use of any accessory or attachment other than
one recommended in this handling instructions or
the HITACHI catalog may present a risk of personal
injury.
23. Repairing must be done only by authorized service
facility. Manufacturer is not responsible for any
damages and injuries due to the repair by the
unauthorized persons as well as the mishandling of
the tool.
24. Have your tool repaired by a qualified person. This
power tool complies with the relevant safety rules.
Repairs should only be carried out by qualified
persons using original spare parts, otherwise this
may result in considerable danger to the user.
25. To ensure the designed operational integrity of
power tools, do not remove installed covers or
screws.
26. Do not touch movable parts or accessories unless
the power source has been disconnected.
27. Use your tool at lower input than specified on the
nameplate; otherwise, the finish may be spoiled and
working efficiency reduced due to motor overload.
28. Do not wipe plastic parts with solvent. Solvents such
as gasoline, thinner, benzine, carbon tetrachloride,
alcohol, may damage and crack plastic parts. Do not
wipe them with such solvent. Clean plastic parts with
a soft cloth lightly dampened with soapy water.
29. Use only original HITACHI replacement parts.
30. This tool should only be disassembled for
replacement of carbon brushes.
31. The exploded assembly drawing on this handling
instructions should be used only for authorized
service facility.
32. Never cut ferrous metals or masonry.
33. Adequate general or localized lighting is provided.
Stock and finished workpieces are located close to
the operators normal working position.
34. Wear suitable personal protective equipment when
necessary, this could include:
Hearing protection to reduce the risk of induced
hearing loss.
Respiratory protection to reduce the risk of
inhalation of harmful dust.
Gloves for handling saw blades (saw blades shall
be carried in a holder wherever practicable) and
rough material.
35. The operator is adequately trained in the use,
adjustment and operation of the machine.
36. Refrain from removing any cut-offs or other parts
of the workpiece from the cutting area whilst the
machine is running and the saw head is not in the
rest position.
PRECAUTION FOR COMPOUND SAW
1.
Never use the compound saw with its safety cover
locked in the open position.
2.
Ensure that the safety cover moves smoothly.
3.
Do not use the saw without guards in position.

Publicidad

Tabla de contenido
loading

Tabla de contenido