Velleman CAMCOLD17 Manual Del Usuario página 4

• Be very careful not to touch any other part inside the housing while setting the switches, as damage
might occur.
• D1~D7 are used to set the ID of the device, allowing for a system with up to 64 unique devices. Refer
to the table below (Θ indicates dipswitch in the ON-position).
• The devices can be controlled using a Pelco controller (not included, e.g. CAMCOLSD1C, CAMCOLD/CK)
or a DVR (not included, e.g. DVR4MQAEE, DVR4H, 3GSYSTEM, DVR8N2).
Note: when using an IR remote control device (not included, e.g. CAMCOLD17RC), only the 9 first
(lowest) IDs can be controlled.
ID D7 D6 D5
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16 Θ
17 Θ
18 Θ
19 Θ
20 Θ
21 Θ
22 Θ
23 Θ
24 Θ
25 Θ
26 Θ
27 Θ
28 Θ
29 Θ
30 Θ
31 Θ
32 Θ
• D8: Baud rate: ON = 4800bps; OFF = 2400bps
• D9: Protocol: ON = PELCO_P protocol; OFF = PELCO_D protocol
• D10: Termination: ON = 120Ω terminal resistor; OFF = high resistor
Note: 1 camera must terminate the databus with a 120Ω resistor; all other cameras on the databus
must have a high input resistor.
Factory settings: PELCO_D, 2400bps, ID #01
15/05/2009
D4 D3 D2
Θ
Θ
Θ
Θ
Θ Θ
Θ Θ
Θ
Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ
Θ
Θ
Θ
Θ Θ
Θ Θ
Θ
Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ Θ Θ
D10 D9 D8 D7
Θ
CAMCOLD17
D1 ID D7
Θ 33
34
Θ 35
36
Θ 37
38
Θ 39
40
Θ 41
42
Θ 43
44
Θ 45
46
Θ 47
48
Θ 49
50
Θ 51
52
Θ 53
54
Θ 55
56
Θ 57
58
Θ 59
60
Θ 61
62
Θ 63
64 Θ
D6 D5 D4
4
D6 D5 D4
Θ
Θ
Θ
Θ
Θ
Θ
Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
Θ Θ Θ
D3 D2 D1
Θ
©2008 Velleman
D3 D2 D1
Θ
Θ
Θ Θ
Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ
Θ
Θ Θ
Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ
Θ
Θ Θ
Θ
Θ Θ
Θ Θ
Θ Θ Θ
Θ
Θ
Θ Θ
Θ
Θ Θ
Θ Θ
Θ Θ Θ
Components nv
®