Inserting The Batteries; Becoming Acquainted With The Remote Control; Connecting The Components; Switching The Device On And Off - Silvercrest KH2307-02 Instrucciones De Uso

Inserting the batteries

You can equip the micro system with 2 x 1,5 V Type AA batteries
so that in the event of a power failure the saved time and
timer information will not be lost. The remote control requires
2 x 1,5 V Type AAA batteries.
Batteries for the retention of data during a power failure are
not supplied.
> Open the battery compartment on the rear panel of the
device 3! and on the underside of the remote control 4$.
> Insert the batteries, ensuring that you observe the polarity
markings as indicated in the battery compartment.
> Carefully close the corresponding battery compartment
lid until it locks into place.
If the device no longer reacts reliably to the remote control
signal, then the batteries are depleted. Change the batteries
with fresh ones of the same type.

Becoming acquainted with the remote control

Point the remote control towards the device when you activate
its buttons. The remote control functions at a distance of approx. 5m
from the device and at an angle of at least 60°. For transmission
of the signal there must be no objects placed between the
device and the remote control.

Connecting the components

Loudspeakers
> Connect the speaker cable of the right speaker to the
right speaker connection "SP R" 2^ on the device.
> Connect the speaker cable of the left speaker to the
left speaker connection "SP L" 2& on the device.
Power supply
> Connect the power plug of the power cord
connected 230 V ~ /50 Hz power socket.

Switching the device on and off

> To switch the device on move the function switch
CD/MP3-, RADIO- or AUX position and press the POWER
button 2). The Micro system is now operational and the
red POWER indicator h as well as the blue background
illumination of the display j light up.
> To switch the device off either move the function switch
to the BUZZ position or press the POWER button 2).
> To disconnect the device from the mains power pull the
power cord plug 3) out of the mains socket.

Setting the time

> Hold down the TIME SET
the HOUR/MIN buttons 2!, the current time in hours
and minutes. For this you can either repeatedly press the
HOUR/MIN button 2! or hold it down.
> Susequently release the TIME SET
day is now saved and appears in the display even when
the device is switched off.
3) to a properly
q to the
2# button while you enter, with
2# button. The time of

Selecting the programme source

You can select between the following programme sources:
• CD/MP3 - Playback of audio CDs or MP3-CDs
• RADIO - Playback of radio stations
• AUX - Playback of a device connected to the
AUX input 2$
> For this move the FUNCTION switch

Setting the sound volume levels

> To increase the volume, repeatedly press the VOL +
or hold the button down until the device has reached the
desired volume level.
> To decrease the volume,repeatedly press the VOL —
or hold the button down until the device has reached the
desired volume level.

Using headphones

You can connect headphones to the micro system with a 3.5mm
jackplug (not supplied). The headphones socket
on the left side of the micro system. When the headphones are
connected, the loudspeakers are switched off and you will
only hear sound via the headphones.
IMPORTANT! Listening to music with headphones
over a long period of time and with full volume can
result in loss of hearingf!

Operating the radio

This device receives radio stations on the frequency bands,
Ultra short wave (USW or engl. FM) and Medium wave
(MW or engl. AM).
> In order to receive a good USW reception with the micro
system unwind the dipole antenna 2( on the rear panel of
the device completely.
> If the reception is insufficient change the position of the
dipole antenna 2(. Secure the dipole antenna 2(, if
necessary, with sticky tape.
> The device has a built in ferrite antenna for reception
of MW stations. When the MW reception is insufficient
please turn the device in a more favourable direction.
> To activate the radio function move the function switch
to the "RADIO" position.
> Now select with the
q
frequency band FM or AM depending on which band
the station that you want to listen to is located. When the
switch is in the FM ST. position the device only plays
USW stations that transmit their programmes in stereo.
> With the help of the TUNING controller
select the station. For this turn the controller in a clockwise
direction to select stations with a lower broadcast frequency
than the one currently shown in the display j.
> Turn the TUNING controller
to select stations with a higher broadcast frequency than
the one currently shown in the display j .
> If the device receives USW broadcasts in stereo the "FM.
ST" indicator g lights up.
> If the stereo reception becomes noisy move the
switch w to the FM MO position and thus switch to mono.
- 28 -
q to the desired position.
2% is located
Radio band switch w the desired
e you can now
e in a counter clockwise direction
Radio band
k button
l button
q