Operating Instructions - Ritter E 118 Instrucciones De Uso

Unfold the illustrations at the
front and back of this manual.
Please read these instructions
thoroughly before you start to
use the appliance. Keep these
operating instructions in a safe
place and ensure that they are
included with the appliance if
passing it on to a third party.
Alternatively, these operating
instructions are available at
www.ritterwerk.de.
INTENDED USE
The multi slicer is used to slice
household foods.
If the appliance is used for a
purpose other than this, or if it
is operated incorrectly, severe
injuries may occur or the
appliance may be damaged.
All warranty and liability claims
will be rendered null and void in
this case.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
Before you use the appli-
ance for the irst time, have a
specialist install it in a suitable
drawer.
Clean the appliance before
allowing it to come into contact
with any food (see CLEAN-
ING).
Setting up the appliance
• Set the appliance down on a
lat, non-skid surface close to a
mains socket.
Using a small amount of
force, push the slice car-
riage (8) vertically into the
guide groove on the appliance
until it audibly locks into place.
Slide the left-over holder (9)
onto the slice carriage's handle.
Unwind the mains cable (5)
to the length required from the
cable compartment (10) under
the appliance and insert the
mains plug into the socket.
SLICING
Use the slice thickness
adjustment knob (2) to set the
required thickness.
Note:
The slice thickness adjustment
scale is not a millimetre scale.
For safety reasons, the
"0" position is designed to
cover the blade.
Place the food to be sliced
onto the slice carriage (8). Use
the left-over holder (9) to press
it up against the stop plate (11).
Protect your hands, by
always using the slice carriage
and, where applicable, the left-
over holder. Exception: Exces-
sively large foods to be sliced.
Turn the appliance on using
the switch (1). Two operating
modes are available:
Temporary operation: Press
the switch and slide it towards
the arrow until you feel some
resistance. The rotary blade (6)
runs as long as the switch is
pressed and held down in this
position.
Continuous operation: Press
the switch and slide it towards
the arrow beyond the resist-
ance point until it latches into
place. The rotary blade runs
without the switch having to be
pressed and held down, until
you push the switch back into
the "0" position.
Note:
Never use the appliance
for more than a maximum
of 5 minutes in continuous
operation.
• With the appliance running,
gently feed the food to be
sliced into the path of the rotary
blade.
• When inished slicing, wait
until the rotary blade has come
to a complete stop.
• After each use, turn the slice
thickness adjustment knob
to the "0" position, in order to
cover up the sharp rotating
blade and to avoid any injuries.
Pull the slice tray (3) to the
right and out of the appliance.
CLEANING
Caution:
Switch the appliance off
before cleaning it; pull the
mains plug out off the socket
and turn the slice thickness
adjustment knob (2) to the
"0" position.
Clean the multi slicer regularly
to prevent the accumulation of
food residue. The rotary blade
must also be cleaned regularly
as described below to prevent
its surface from rusting.
Note:
Over time, an accumulation of
food residue may cause dam-
age to the surface of the rotary
blade, causing it to rust.
Preparation
• Remove the slice tray (3)
and the left-over holder (9).
Pull the slice carriage (8)
forward and then lift it up and
out of the guide groove.
Removing the rotary blade:
Place a suitable coin on the
blade catch (7) and turn it in an
anticlockwise direction.
• Take hold of the rotary blade
at its rotational centre and
remove it.
English
11