Clatronic CL 3672 Manual De Instrucciones página 32

16 Control lamp FAN
17 TIMER button
18 SPEED button
19 MODE button
20 IR receiver for remote control
21 TEMP − button
22 TEMP + button
23 POWER button
Delivery Scope
1 Air conditioning appliance
1 Remote control
2 Batteries
1 Flexible exhaust pipe
1 Exhaust pipe adapter (Connection on the appliance)
1 Window kit, 2-piece
1 Adapter for the window exhaust kit
1 Water hose, Ø 16 mm
2 Rubber caps (spares)
2 Plugs (spares)
Unpacking the Appliance
1. Remove the appliance from its packaging.
2. Remove all the packaging material such as plastic bags, fi ller material,
cable ties and cardboard packaging.
3. Check that all parts are supplied in the package.
Notes on Use
CAUTION: Important for initial operation or after transport!
Before initial operation, the appliance must stay in an upright position for
at least 3 hours in order for the cooling agent to sink. The compressor
will be damaged otherwise.
CAUTION:
• When you interrupt the operation with the POWER
at least 3 minutes before switching the appliance on again.
• If you want to move the appliance to another location, fi rst empty the
water tank!
NOTE:
You will fi nd all operating buttons on both the appliance and the remote
control. Same buttons represent the same functions.
• The appliance operates most effectively with a room size up to 70 m³.
• The fl exible exhaust hose and the adapter (6) have been manufactured
especially for this appliance. In order to avoid incorrect operation, do not
replace the pipe with another pipe.
• The exhaust pipe can be extended up to 150 cm. Do not use any
extension.
• Ensure free airfl ow. Make sure not to kink or bend the exhaust pipe. Any
blockage can cause the appliance to overheat.
• Close all windows and doors in order to prevent outside air from
entering the room and thus allowing a more effective operation of the
appliance.
Initial Operation
Location
• When installing the appliance, make sure to keep a distance of at least
30 cm between the appliance and any walls or other objects.
• The surface must be fl at and dry.
32
CL3672_IM_new_Dec_2018
Assembly of Exhaust Pipe
NOTE:
For sliding windows, you may use the window kit provided and install it
in a vertical or horizontal position. Adjust the length of the seal plate as
desired.
1. Turn the adapter (6) to one end of the exhaust pipe.
2. Connect the exhaust pipe to the appliance using the exhaust pipe
connector. Set the adapter fi rst on the left side. Press the adapter on
the right side down into the linkage.
3. Extend the pipe to the desired length.
4. Stick the open end of the pipe into a window.
5. Close the window as far as possible. Also lower any external roller
blinds, if present, to the end of the pipe.
Remote Control
1. Open the battery compartment cover on the back of the remote
control.
2. Insert 2 batteries of type R03 "AAA" 1.5 V, observing the correct polarity
(see markings on the bottom of the compartment)!
3. Close the battery compartment cover.
Electric Connection
1. Make sure the mains voltage you want to use corresponds to the
voltage of the appliance. Please check the rating label for detailed
specifi cations.
2. Connect the appliance to a properly installed grounded socket. A signal
will sound indicating that the appliance is ready for use.
Turning Appliance On / Off
• Press the POWER
is pre-set to "Cooling" mode and the temperature is 25 °C. If operation
has been stopped without disconnecting the plug, all previously set
operating mode and temperature settings will be retained. The control
button, wait for
lamps indicate this setting.
• Press the POWER
Compressor Safety Appliance
If operation is interrupted, the safety appliance for the compressor is acti-
vated. This prevents operation of the compressor for approx. 3 minutes, in
order to relieve the pressure in the cooling circuit. This is not a malfunc-
tion of the appliance. Therefore, wait at least 3 minutes, before switching
the appliance on again.
Control Panel
Button
POWER
TEMP +
TEMP −
MODE
SPEED
TIMER
-
Using the Appliance
button to turn on the appliance. The appliance
button again to turn off the appliance.
Control lamp
- Turn on / off
- Increase temperature
- Reduce temperature
COOL (Cooling)
DEHUM (Dehumidifying) Select operating mode
FAN (Fan)
HIGH (High speed)
Set fan speed
LOW (Low speed)
TIMER Timer operation
W.F Water must be emptied.
Explanation
12.12.2018