Technical Data; Double Insulation - Narex EPL 12-7 BE Instrucciones De Uso

Technical Data

Hand jigsaw
Type
Voltage
Power frequency
Rated power input
Number of strokes in idle cycle
Electronic stroke number selection
Pendulum stroke setting
Hoisting
Cut-through in timber
in colour metals
in steel
Chamfer cuts
Quick coupling blade system*
Weight
Protection class
*(System of tool-less circular-saw blade clamping)
Controllers
1 ............Clamping lever
2 ............Saw blade clamp
3 ............Saw blade
4 ............Additional saw blade guide
5 ............Additional guide set screw
6 ............Splinter guard
7 ............Jig saw base runner
8 ............Base runner pad
9 ............Splinter guard locking nose
10 ..........Chip guard
11 ..........Extraction channel
12 ..........Extraction adapter
13 ..........Extraction hole
14 ..........Extraction adapter lock
15 ..........Extraction adapter lock retaining groove
16 ..........Base runner set screw
17 ..........Hexagonal (Allen) wrench
18 ..........Base runner slope scale
19 ..........Pendulum stroke change over switch
20 ..........Guide bell
21 ..........Rod
22 ..........Stroke controller
23 ..........Switch button
24 ..........Switch lock button
25 ..........Centering base runner pin
26 ..........Centering base runner hole
27 ..........Guide for straight cuts
28 ..........Guide for circular cuts (circle cutter)
29 ..........Clamping clip for the guide
30 ..........Parallel guide stop
31 ..........Guide locking screw
32 ..........Hole for the circle cutter pin
33 ..........Circle cutter pin
34 ..........Steel base runner pad
35 ..........Vent holes
The displayed or described accessories do not necessarily become the
integral part of jig saw delivery.

Double insulation

To ensure maximum safety of the user, our tools are designed and built
to satisfy applicable European standards (EN standards). Tools with
double insulation are marked by the international symbol of a double
square. These tools must not be grounded and a two-wire cable is suf-
ficient to supply them with power. Tools are shielded in accordance with
EN 55014.
EPL 12-7 BE
230–240 V
50–60 Hz
720 W
1 000–2 900 spm
ü
4 stages
26 mm
120 mm
20 mm
10 mm
±45°
ü
2.4 kg
II /
Scope of Use
The jig saws are designed and intended for shaped and direct cutting
of wood, plastics, steel, non-ferrous metals, aluminium and ceramics.
They are suitable for straight and arc cuts under the angle of ±45°. Use
the saw blades recommended by the manufacturer for the operations
above.
The user is responsible for improper use.
Saw Blade Clamping and Removal
Attention! Risk of el. shock. Prior to start any operation,
pull the plug out of the socket!
To clamp the saw blade (3), tilt the clamping lever (1) fully by one hand
and insert the saw blade (3) by the second hand as far as the stop of the
saw blade clamp (2). Then release the clamping lever (1) and move it to
the initial position. (The clamping lever is equipped by a spring ensuring
its tilting towards the jig saw body).
To remove the saw blade (3), tilt the clamping lever (1) fully by one hand
and remove the saw blade (3) by the second hand (3) out of the saw
blade clamp (2). If a new saw blade is not inserted, release the clamping
lever and move it back to the initial position.
Saw blade guide setting (4)
For better guidance of the saw blade (3) the jig saw is equipped by the
additional hard metal guide (4) mounted immediately above the work-
piece.
Using the Allen key (internal part of the scope of delivery), screw or un-
screw the additional guide set screw (5) until the guide jaws (4) nearly
rest against the saw blade (3).
The saw blade clearance must guarantee its easy movement!
Splinter Guard
The splinted guard (6) allows cuts with splinter-free edges even on
the side of the cut material which the saw blade base runner (7) leans
against (except special saw blades with inverse saw teeth).
Attention! Risk of injury in case of unwanted start of the
tool. Prior to start any operation, pull the plug out of the
socket!
‰ Insert the splinter guard (6) into the base runner pad (8) and push it
as far as the saw blade. Attention, the locking nose (9) in the side
groove of the splinter guard (6) must be up with respect to the
position of the jig saw base runner (7).
‰ Set the pendulum stroke (see the chapter "Pendulum Stroke Set-
ting") to position 1 or 2.
‰ Start the jig saw (see the chapter "Putting into Operation").
English
19