Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT: Pull the Skate bassinet unit
upwards to check that it is correctly attached.
IMPORTANT: If the Skate bassinet unit is
incorrectly attached, remove it from the Skate
chassis and correctly repeat the procedure
described above.
IMPORTANT: Do not place a child in the
Skate bassinet unit before opening the Skate
chassis.
1 3•FRONT BAR/CARRYING HANDLE: To fit
the front bar, put its attachments in their
housing while pressing on the safety buttons
and pushing upwards until the two clicks
confirm it is in place. The front bar can only
be attached to the Skate bassinet unit in one
direction.
1 4•The front bar can be set in 2 positions: a
lower position (1) for use as a front bar and
a higher position (2) for use as a carrying
handle (Fig.a).
To carry a child – which is only possible in
Skate bassinet unit mode and with a child
who weighs less than 9 kg – use it in the
higher position (2).
To adjust it, open the two levers inwards,
position the front bar in the desired position,
and close the two levers (Fig.b).
1 5•To release it, press the side buttons on the
Skate bassinet unit and pull the attachments
of the front bar downwards (Fig.a).
The front bar opens and closes to facilitate
the entry and exit of children when they get
bigger (Fig.b).
To open it, press the two round buttons at the
same time and pull the front bar outwards.
To close it, do the opposite.
1 6•BACKREST: It can be set in 3 positions.
To put the backrest in the required position,
put the pin in one of the 3 eyelets in the
central belt, which can be found on the rear
of the backrest (Fig.a).
COVER: Button it down on both sides and
attach the elastic loops to the clips on the
sides of the front bar (Fig.b).
1 7•RELEASING the Skate bassinet unit from the
Skate chassis: Put the front bar in the high
position (carrying handle position), take hold
of it and pull it upwards (1), release the Skate
bassinet unit first on one side (2) and then on
the other (3), pressing on the release levers.
IMPORTANT: Only carry out this procedure
with the child in the seat if it is in Skate
bassinet unit mode and if the child weighs
less than 9 kg.
SKATE SEAT
18•Before attaching it to the Skate chassis, it is
necessary to press the backrest and move
from the inside to the outside to ensure that
the seat is completely open (Fig.a).
• Attach the front bar (paragraph 13).
• ATTACHING the Skate seat to the Skate
chassis: To attach the Skate seat, position
its couplings in their housing on the Skate
chassis and click them into place (Fig.b).
IMPORTANT: Do not place a child in the Skate
seat before opening the Skate chassis.
1 9•REVERSIBILITY: The Skate seat is reversible; it
can be attached to the Skate chassis facing
the person pushing or facing forwards.
2 0•INCLINING Skate seat: The Skate seat can
be inclined at 3 different angles (horizontal,
inclined and vertical) both when facing the
person pushing and when facing forwards.
To incline the Skate seat, raise the handle
behind the backrest and position it as
required.
2 1•5-POINT SAFETY HARNESS: To fasten the
harness, push the two waist strap buckles
(with the shoulder straps attached as shown
by arrow a) into the leg divider strap until
they click into position (arrow b). To unfasten
it, push the round button in the centre of the
buckle upwards (arrow c) and pull the waist
straps outwards (arrow d).
2 2•To tighten the waist straps, pull from both
sides in the direction of the arrow (Fig.a);
to loosen them do the opposite. The waist
straps can be tightened as far as the safety
stop (Fig.b).
2 3•To adjust the height of the safety straps, it is
necessary to unfasten the buttons from both
sides of the Skate fabric covering (paragraph
39 b) and lift off the fabric covering.
Pull the buckles towards you (arrow a), then
slip them through the slots in the backrest
(arrow b). Pull the shoulder straps through
the fabric covering (arrow c) and push them
through the most suitable slot (arrow d), then
position the two buckles behind the backrest
(arrow e) below the support straps (fig f).
2 4•COVER: Button it down on both sides (Fig.
a) and attach the elastic loops to the clips on
the sides of the front bar (Fig.b). Attach the
elastic loops under the footrest (Fig.c).
With the Skate seat, the zipper of the cover
can be opened to increase the space available
for the child's feet (Fig.d).
2 5•The HEIGHT of the Skate bassinet unit and
Skate seat is ADJUSTABLE: they can be set at
3 different heights.
Simultaneously press the two side buttons on
the Skate chassis and at the same time raise
or lower the Skate bassinet unit or Skate seat
until you hear them both click into place.
Look at the arrows on the Skate chassis to
check that it is correctly in position.
The procedure is also possible with the Car
Seat attached.
- 22 -
Publicidad
