Descargar Imprimir esta página

Vitamix Ascent Serie Manual De Usuario página 6

Ocultar thumbs Ver también para Ascent Serie:

Publicidad

Idiomas disponibles

Idiomas disponibles

Note: The cups mentioned here are optional accessories of the Ascent Blenders. Please visit www.vitamix.com for more information.
To Avoid Possible Burns, Never Start on Speeds Above 1 when Processing Hot Liquids in a Large Container.
Escaping steam, splashes or contents may burn. Always start on Variable 1, then slowly increase to 10.
DO NOT use your 20 ounce cup or 8 ounce cup to heat ingredients or to blend hot liquids. Heated ingredients and
liquids may create internal pressure which could cause the cup to burst and cause injury.
DO NOT continuously use your machine for more than 75 seconds when blending with a cup and blending adapter.
If a cup becomes warm to the touch or steams or vents, immediately stop blending ingredients and turn off or
unplug blender. Allow the cup and ingredients to cool to room temperature before removing the blending adapter.
Parts will become hot with extended use.
DO NOT touch the drive socket in the motor base or the drive spline in the adapter.
To avoid damage or personal injury, DO NOT use the cups (including the adapter or lids) in the microwave.
IMPORTANT! Always use the lid and the lid plug on the Large Container when the
machine is in operation. Never operate the blender without checking to make sure
that the lid and lid plug are securely locked in place. After blending, wait until the
blades completely stop before removing the lid or container/cup from the blender
base.
1.
The On/Off switch is on the right hand side of the base. Press the On/Off switch
to the On (I) position. After the blender is turned on, "Vitamix" will appear on the
control panel. This symbol
container is on the blender base.
2.
Load your container according to your recipe or the load order below.
Ice & Frozen
Ingredients
Fruits & Veggies
Leafy Greens
Dry Goods
Liquids
Note: Ingredients for cups load in the
opposite order of the large containers.
Liquids
Dry Goods
Leafy Greens
Fruits & Veggies
Ice & Frozen
Ingredients
6
will be displayed on the control panel when no
Large Containers
20 ounce Cup
b
l e n d i n g
WARNING
3.
Perform one of the following:
• Large Containers - Put the lid onto the container. Push the lid down into place
until the two tabs snap onto the lip of the container. Insert the lid plug. Turn the
lid plug clockwise to lock.
• Cups -
Locate the arrows on the blade base and cup or bowl. The arrows are
important alignment features to ensure safe use of the product. Put a seal on the
bottom thread of the blade base. The seal should fit snugly and evenly around the
thread. Thread the blade base onto the cup or bowl in a clockwise direction. Tighten
the blade base onto the bowl or cup until the arrows line up. DO NOT overtighten or
leaking can occur.
4.
Put the container (or cup and adapter) onto the base. Variable Speed 1 will display
when a container/cup is detected and the blender is ready to operate.
5.
Perform one of the following:
• To use variable speed:
a. Turn the variable speed dial counter-clockwise until Variable Speed 1
appears on the control panel.
b. Press Start/Stop. The blades will begin to turn and the timer will count the
minutes and seconds that the blend has been processing. To set a blend
time, use the +/- icons on the controls.
c. Rotate the Variable Speed Dial between 1 and 10 during the blending cycle
to increase or decrease the speed of the blades.
d. At the end of the blend, rotate the Variable Speed Dial counter-clockwise
until Variable 1 is displayed and press Start/Stop.
• To use Programs:
Note: The soup program is not available for use with the cups. DO NOT
blend hot liquid in the cups.
a. Press the icon for the desired program. (The default program time and
variable speed setting will display on the control panel).
b. Press Start/Stop to start the program. (The blender will automatically stop at
the end of the program.) Press Start/Stop at any time to stop the program.
6. If the mixture stops circulating:
• Large Containers - Insert the tamper through the lid plug and stir until it 'burps'.
If this does not work, press the On/Off switch to stop the motor. Remove
the container from the blender base and use a rubber spatula to press the air
bubble away from the blades. Add liquid if necessary. Replace the lid and lid
plug. Return the container to the blender base and continue blending.
• Cups - Press the Start/Stop to stop the motor. Wait until the blades stop
rotating. Remove the cup and adapter from the blender base. Turn the cup
over. Unthread the adapter from the cup. Stir the ingredients. Add liquid if
necessary. Reattach the adapter, place on blender base and continue blending.
IMPORTANT! Tighten the blade base onto the bowl
or cup until the arrows line up with the arrow on the
bowl or cup.
Blade Base
Bowl or Cup

Publicidad

loading

Este manual también es adecuado para:

Ascent a2300Ascent a2500