Confirm Before Operation; About The Registered Marks Etc; Specifications - Clarion DVC920 Manual De Instrucciones

Basic Operations
• ST-96K: Stereo sound with 96kHz sampling • STADIUM(Stadium):Large stadium without
frequency roof or walls.
• Lt/Rt: 2-channel audio including surround • LIVE(Live):Live performance hall, larger than
sound a jazz club.
• 1+1: Discrete monaural sound • JAZZCLUB(Jazzclub):Jazz club with a low
ceiling.
• 1/0: Front 1-channel sound
• THEATER(Theater):Movie or drama theatre.
• 2/0: Front 2-channel sound
• The original mode is resumed when the
• 2/1: Front 2-channel sound; surround mon-
button is not pressed during a 7 second
aural sound
interval.
• 2/2: Front 2-channel sound; surround 2-
channel sound
Adjusting the sound volume
• 3/0: Front 3-channel sound
balance of each speaker
• 3/1: Front 3-channel sound; surround mon-
(AUDIO MODE)
aural sound
You can adjust the sound image to suit the seat-
• 3/2: Front 3-channel sound; surround 2-
ing position and number of passengers.
channel sound
1. Press the [A-MODE] button.
• */*+LFE: Low-frequency channel sound
Each time the [A-MODE] button is pressed,
• NoSIGNAL: No digital signal is input
the indications change as shown below.
• ————: Current input signal is other than [SUB-W] → [CTR] → [BAL] → [FAD] →
linear PCM, Dolby digital DTS
original mode
• Fs ERR: Current signal input has sampling
• The original mode is resumed when the but-
frequency other than 32kHz, 44.1kHz,
ton is not pressed during a 7 second inter-
48kHz, or 96kHz.
val.
• CLIP: DSP output clipping
2. Press the [
Note: the value.
• When signals are input from the ANALOG 1 con-
G SUB-W (Sub woofer):
nector or CeNET input connector, they are indi-
cated by the [STEREO] display. Adjusts sub woofer volume.
The volume is adjusted in the range –6 to +3.
DSF setting
G CTR (Center speaker):
DSF (Digital Sound Field) makes it possible
Adjusts center speaker volume.
through sound simulation to enjoy the acoustic
experience you would have in a concert hall or a The volume is adjusted in the range –6 to 0.
live performance hall.
G BAL (Balance):
Any one of six sound effect patterns can be ap-
Adjusts the sound volume in the left and right
plied to the sound in the signal formats DTS,
speakers.
Dolby Digital, or Linear PCM (or after decoding
The sound volume is adjusted in the range
Dolby Pro Logic II signals).
L13 to R13.
• The initial setting is [DSF OFF].
G FAD (Fader):
1. Press the [DSF] button.
Adjusts the sound volume in the front and rear
Each time the [DSF] button is pressed, the in-
speakers.
dications change as shown below.
The sound volume is adjusted in the range
[DSF OFF] → [HALL] → [CHURCH] →
[STADIUM] → [LIVE] → [JAZZCLUB] → R12 to F12.
[THEATER] → [DSF OFF]
Mute
• HALL(Hall):Large concert hall.
Each time you press the [MUTE] button, mute is
• CHURCH(Church):Church with a vaulted
turned on and off.
ceiling.
"MUTE" appears when mute is turned on.
8
DVC920
280-7804-00_02-08(En) 3

1. CONFIRM BEFORE OPERATION

G This component has not been designed to operate as an independent unit by itself, and
must be used in conjunction with a 5.1ch surround decoder. For information about Clarion
center units and DVD changers that can be connected to this component, see the sec-
tion "SYSTEM EXPANSION" on P17. Alternately, consult your retail dealer or Clarion
service center.
G When connecting this component (control unit), be sure to set the 5.1ch surround decoder's
[STAND-ALONE / SLAVE] switch to the [STAND-ALONE] position. Also be sure to con-
nect the power cable.
G In order to demonstrate optimum audio performance, be sure to change the default set-
tings of the adjust mode's [SP-SEL], [FILTER], [SP-GAIN] and [DELAY] functions (see
P9-13).
I Using Analog Input Connections
• When connecting the RCA 2ch output of another component (center unit, etc.) to the analog
INPUT connectors, the Dolby Pro Logic II function can be used to convert to 5.1ch output.
Set the [STAND-ALONE / SLAVE]
switch to the [STAND-ALONE] position.
] or [ ] [VOL] button to adjust
STAND
SLAVE
ALONE
Analog INPUT connectors
Center Unit
Audio OUTPUT connectors
NOTES:
• When using the analog INPUT connectors, consult the section
"Adjusting the RCA INPUT sensitivity" on P13 and adjust the
sensitivity properly to prevent audio distortion.
• Consult the section "Setting the Dolby digital functions" on
P11 and select the desired Dolby Pro Logic II mode.
DVC920
2/22/02, 2:05 PM

About the registered marks etc.

• Manufactured under license from Dolby Labo- • Manufactured under license from Digital The-
ratories. ater Systems, Inc. US Pat. No. 5,451,942,
5,956,674, 5,974,380, 5,978,762 and other
"Dolby", "Pro Logic" and duble-D symbol are
world-wide patents issued and pending.
trademarks of Dolby Laboratories.
"DTS" and "DTS Digital Surround" are regis-
tered trademarks of Digital Theater Systems,
Inc. © 1996, 2000 Digital Theater Systems, Inc.
All Rights Reserved.

2. SPECIFICATIONS

Control unit List of accessories
Power Supply Voltage: 1. Control unit .................................................. 1
14.4 V DC (10.8 to 15.6 V allowable) 2. Owner's manual .......................................... 1
Ground: Negative 3. Warranty ...................................................... 1
Current Consumption: Less than 3 A 4. Control unit cord .......................................... 1
Weight: 5oz. (150 g) 5. Power supply harness ................................ 1
Dimensions: 6. Parts bag (1)
6 5/16" Width × 1 9/16" Hight × 13/16" Depth
• Cord clamps (small) ................................. 2
(160 mm Width × 39 mm Hight × 20.6mm Depth)
• Cord holders ............................................ 2
• Velcro tape (medium) .............................. 2
• Velcro tape (small) .................................... 2
Note:
• Specifications and design are subject to change
without notice for further improvement.
Be sure to unfold and read the next page. / Veuillez déplier et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
3 4
DVC920
280-7804-00