Switching The Angle; Changing The Brightness Of The Display (Dimmer Control); Hdmi Control Function - Denon DBP-4010UDCI Manual Del Usuario

ENGLISH
Operations Enabled During Playback

Switching the Angle

During playback of a BD or DVD-Video recorded with several
camera angles, you can change the angle.
1
Press during playback.
The·angle·number·currently·being·played·is·displayed.
Angle
1/3
2
Use to select angle.
Angle
2/3
3
Press .
The·setup·screen·disappears.
NOTE
Angle·changing·may·be·restricted,·depending·on·the·disc.·
Changing the Brightness of the
Display (Dimmer Control)
Press .
The· display· brightness· each· time· the· button· is·
pressed.
Normal·· ··Dim··
Even· when· "Off"· is· selected,· the· status· of· operations· that· are·
performed· appears· momentarily· on· the· display· if· "Display· Setup"·
–·"Temporary·Display"·on·the·GUI·menu·is·set·to·"On"·(vpage·30).


HDMI Control Function

When·you·make·an·HDMI·connection·with·a·TV·or·AV·Amp·compatible·
BD DVD-V
with· DBP-4010UDCI· and· HDMI· control· functions,· you· can· perform·
the·following·operations·by·setting·the·HDMI·control·function·of·each·
device.·
TV or AV Amp power is turned on by operating the
n
DBP-4010UDCI, and functions change with DBP-
4010UDCI input.
Turning off the TV's power turns the DBP-
n
4010UDCI's power to standby.
Operating the DBP-4010UDCI via the TV's remote
n
control.
(When the TV's remote control has player operation buttons)
NOTE
• The· HDMI· control· function· controls· operations· of· a· TV· that· is·
compatible·with·the·HDMI·control·function.··Make·sure·that·the·TV·
and·HDMI·are·connected·when·you·perform·HDMI·control.·
• Some·functions·may·not·operate·depending·on·the·connected·TV·
or· AV· Amp.· Check· the· owner's· manual· of· each· device· for· details·
beforehand.
• When· "Other· Setup"· –· "Power· Saving"· on· the· GUI· menu· is· set·
to· "Power· Saving· Standby"· or· "Normal· Standby"· (vpage· 31),·
the· player's· power· cannot· be· turned· on· using· the· HDMI· control·
function.
• When·"HDMI·Setup"·–·"HDMI·Control"·–·"Power·Off·Control"·on·the·
GUI·menu·is·set·to·"Off"·(vpage·24),·the·DBP-4010UDCI·is·not·set·
to·standby·even·if·the·connected·device·is·in·the·standby·mode.
• When· "DENON· LINK· Setup"· –· "DENON· LINK· Mode"· on· the· GUI·
menu·is·set·to·"4th",·the·HDMI·control·function·is·enabled·for·the·
connected·devices.
··Dark· ··Off
1
Set HDMI control function to "On".
On·the·GUI·menu,·set·"HDMI·Setup"·–·"HDMI·Control"·(vpage·
24).
2
Turn the power on for all the equipment connected by
HDMI cable.
3
Set the HDMI control function for all equipment
connected by HDMI cable.
On· the· GUI· menu,· set· the· DBP-4010UDCI· with· "HDMI· Setup"·
–·"HDMI·Control"·(vpage·24).·
Please·refer·to·the·owner's·manual·as·regards·setting·of·connected·
b
devices.
Carry· out· Steps· 2· and· 3· should· any· of· the· equipment· be·
b
unplugged.
4
To ensure that the DBP-4010UDCI's HDMI video
output is projected on the TV screen, change the
input function of the TV and AV Amp.
5
When you turn the TV's power to standby, check that
the power of the DBP-4010UDCI and AV Amp also
goes on standby.
If· the· HDMI· control· function· does· not· operate· properly,· check· the·
following·points.·
• Is·the·TV·or·AV·Amp·compatible·with·the·HDMI·control·function?
• Are· the· HDMI· control· function· settings· of· all· equipment· correct?·
(Step·3)
• After· setting,· did· you· add· another· HDMI· device· connection· or·
make·any·changes·in·the·connections?·In·this·case,·perform·setting·
again.·