Overview Of The Components / Delivery Scope; Using The Appliance - Profi Care PC-HT 3044 Instrucciones De Servicio

Overview of the Components / Delivery
Scope
1. Compact hairdryer.
2. Cold air inlet.
3. Hot / cold air exhaust.
4. Cool shot button.
5. 0 / I / II Power switch.
6. Handle.
7. Hanging loop.
8. Extra-long coiled power cord.
9. Drilling hole.
10. Wall mount.
11. Wall mount safety shut down button.
12. Power cord.
13. Power plug.
14. Wall plug.
15. Mounting screw.
16. Mounting stud.
Unpacking the Appliance
• Remove the appliance from the packaging.
• Remove any packaging materials that may be present
inside the packaging or inside the appliance.
• Check the overview of the components / delivery scope
and ensure that all of the components are present.

Using the Appliance

Instructions for Use
Before you start to dry your hair for the first time using this
appliance.
• Remove any packaging that is still present. Unwind the
mains lead completely. Make sure there are no knots
in the mains lead that could damage the appliance or
cause any risk to the user.
• Clean the housing, the cold air inlet (2) and the hot /
cold air exhaust (3) with a damp cloth.
• Please ensure the power switch (5) is put into the 0
position.
1. Select an installation location without pipes or cables
behind it. Place the mounting stud (16) with the lower,
thicker side facing the wall, mark the fastening hole and
drill the hole accordingly through the dedicated drilling
hole (9) for the mounting screws (15).
2. Insert the supplied wall plug, place the mounting stud
(16) and screw into place with the supplied mounting
screw (15).
3. Hang the wall mount (10) over the mounting stud (16).
You will hear a click when it is firmly in place. Mark the
fastening holes and drill the holes accordingly through
the dedicated drilling holes (9) for the mounting screws
(15).
4. Insert the supplied wall plugs (14) and fix the wall mount
(10) in place with the supplied mounting screws (15).
5. Hang the hairdryer (1) in the wall mount (10) and ensure
32
the wall mount (10) remains firmly in place.
6. Insert the power plug (13) in a duly installed protective
contact socket.
7. Gently take the hairdryer (1) from the wall mount (10) for
operation.
8. Slide the power switch (5) into the I position. The haird-
ryer (1) switches on and is ready to be used.
NOTE:
Any smoke or smells produced by the appliance
during this procedure is normal. Please ensure for
sufficient ventilation.
9. To increase the temperature of the hot air, slide the
power switch (5) into the II position. The increased
sound production after switching the power switch (5)
into the II position is normal.
NOTE:
• Ensure that the cold air inlet (2) remains free from
any obstructions and remains uncovered during
the use of the hairdryer (1).
• Ensure that the hot / cold air exhaust (3) remains
free from any obstructions and remains uncovered
during the use of the hairdryer (1).
10. In order to use cold air while hair drying press and hold
the cool shot button (4). Cold air will keep coming from
the hot / cold air exhaust (3) until the cool shot button (4)
is released.
11. After use, slide the power switch (5) into the 0 position
to turn the hairdryer (1) off before unplugging the power
plug (13) from the power socket.
12. Remove the power plug (13) from the socket and allow
the hairdryer (1) to cool down.
13. After the hairdryer (1) has completely cooled down,
wipe the housing, the cold air inlet (2) and the hot / cold
air exhaust (3) clean with a paper towel and remove any
hair sticking to the hairdryer (1).
WARNING:
Pay attention to the heated up hot / cold air exhaust (3).
Risk of burning.
CAUTION:
Do not use pointed or sharp objects to avoid damaging
the housing and the internal fans of the hairdryer (1).
Electrical connection
1. Check whether the mains voltage that you want to use
matches the one of the hairdryer (1). You will find the
information about this on the power plug (13).
2. Insert the power plug (13) in a duly installed protective
contact socket.
3. Switch off the hairdryer (1) by sliding the power switch (5)
into the 0 position. The power plug (13) can be removed
from the power socket.