Additional Safety Instructions - Scheppach HM100Lu Manual Del Usuario

11 Do not use the cable for purposes for which it is
not intended
– Do not use the cable to pull the plug out of the out-
let. Protect the cable from heat, oil and sharp edges.
12 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
– An additional support is necessary for long work-
pieces (table, trestle, etc.) in order to prevent the
machine from tipping over.
– Always press the workpiece firmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
13 Avoid abnormal posture
– Make sure that you have secure footing and
always maintain your balance.
– Avoid awkward hand positions in which a sudden
slip could cause one or both hands to come into
contact with the saw blade.
14 Take care of your tools
– Keep cutting tools sharp and clean in order to be
able to work better and more safely.
– Follow the instructions for lubrication and for tool
replacement.
– Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
– Check extension cables regularly and replace
them when damaged.
– Keep the handle dry, clean and free of oil and
grease.
15 Pull the plug out of the outlet
– Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
– During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
16 Do not leave a tool key inserted
– Before switching on, make sure that keys and
adjusting tools are removed.
17 Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
18 Use extension cables for outdoors
– Only use approved and appropriately identified
extension cables for use outdoors.
– Only use cable reels in the unrolled state.
19 Remain attentive
– Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
20 Check the electric tool for potential damage
– Protective devices and other parts must be care-
fully inspected to ensure that they are fault-free
and function as intended prior to continued use
of the electric tool.
– Check whether the moving parts function fault-
lessly and do not jam or whether parts are dam-
aged. All parts must be correctly mounted and all
conditions must be fulfilled to ensure fault-free
operation of the electric tool.
22 GB/IE
– The moving protective hood may not be fixed in
the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is speci-
fied in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
21 ATTENTION!
– Exercise elevated caution for double mitre cuts.
22 ATTENTION!
– The use of other insertion tools and other acces-
sories can entail a risk of injury.
23 Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be per-
formed by an electrician using original spare
parts. Otherwise accidents can occur.

ADDITIONAL SAFETY INSTRUCTIONS

Safety precautions
1
– Warning! Do not use damaged or deformed saw
blades.
– Replace a worn table insert.
– Only use saw blades recommended by the
manufacturer which conform to EN 847-1.
– Make sure that a suitable saw blade for the ma-
terial to be cut is selected.
– Wear suitable personal protective equipment.
This includes:
– Hearing protection to avoid the risk of becom-
ing hearing impaired,
– Respiratory protection to avoid the risk of
inhaling harmful dust,
– Wear gloves when handling saw blades and
rough materials. Carry saw blades in a con-
tainer whenever practical.
– Wear goggles. Sparks generated during work
or splinters, chippings and dust coming from
the device can lead to loss of eyesight.
– Connect a dust collecting device to the electric
tool when sawing wood. The emission of dust
is influenced, among other things, by the type
of material to be processed, the significance of
local separation (collection or source) and the
correct setting of the hood/guide plates/guides.
– Do not use saw blades made of high-speed alloy
steel (HSS steel).
2 Maintenance and repair
– Pull out the mains plug for any adjustment or
repair tasks.
– The generation of noise is influenced by various
factors, including the characteristics of saw
blades, condition of saw blade and electric
tool. Use saw blades which were designed for