Master B 18 EPR Manual Operativo página 12

GB
IMPORTANT!!! Carefully read this service manual before
you start to use, repair or clean the heater. Improper use of the
appliance may cause serious injuries, burns, electric shock or fire.
2. Safety instructions.
The appliance has been designed for heating closed areas such as
e.g. warehouses, shops and houses. Models with power: 2; 3; 3,3;
kW are not designed to work in greenhouses and on buildings site. It
complies with the Directive No. 2006/95/EC and 2004/108/EC
including the harmonised standards No EN 60335-1:2004, EN
60335-2-30:2007.
WARNING! Do not place the heater directly under the wall outlet.
Do not touch internal components of the heater.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
-
Do not cover the heater when it is operating. The appliance
•
may get overheated.
•The heater should be kept at a safe distance from flammable
materials. The minimum safety distance should not be inferior to 0.5
m, otherwise you run the risk of starting the fire.
•Do not use the heater in dusty spaces or rooms where gasoline,
solvents, paints or other volatile and inflammable materials are
stored in order to avoid the risk of explosion.
•The heater should not be used close to the curtains or other textiles
in order to avoid the risk of fire.
•Be particularly cautious when using the heater in the rooms
frequented by children or animals.
•The heater should be supplied from a source meeting the
requirements specified on the rating plate.
•Use only a feeder cable including the earth lead in order to avoid
electric shock in emergency situations.
•Do not unplug the heater by pulling the wire out of the wall socket.
The appliance should cool down through the ventilation effect.
•Unplug the heater when not used in order to avoid accidental
damages.
•Before you dismantle the casing check if the feeder cable has been
pulled out of the wall socket. Internal components may be live.
2. Unpacking and transport.
•Open the package and take the heater out including all the safety
locks installed for the period of transport.
•Should the appliance seem damaged, notify immediately the seller
of the same.
•Transport the heater using the handle No. 1 shown in Figs. 1 page 2.
•The heater should be transported in original package including the
safety locks.
5. Description of individual components.
See Figs. 1, Page. 2.
1) Handle 8) Wheel.
2) Tuba air outlet 9) Base foot.
3) Motor with fan 10) Hiting element.
4) Switch
5) Casing
6)Thermostat external socked
7) Plug
6. Switching on.
WARNING !!!: Carefully read this service manual before you start
to use the heater. The instructions contained herein will allow you
to use the appliance in a safe manner.
Make sure the power supply cable has not been damaged. If the supply
cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
Moreover, check if the technical parameters of power supply source
comply with the requirements specified on the rating plate.
Place the appliance in its upright position. Make sure the switch is in
its "0" position shown in Fig. 4. Connect the heater to the power
supply source. Turn the switch and leave it for 5 seconds in the
positions as follows:
•Fan only: Figs. 2,3 swith A turn on
st
degree of heating: Figs. 2,3 swith C turn on
•1
nd
degree of heating: Figs. 2,3 swith B,C turn on
•2
nd
degree of heating: Figs. 2,3 swith B,C,D turn on
•3
5. Switching off.
Turn the switch to its "0" position. Once the heating is off, leave the
fan operating for 3 minutes.
11. Work with the hose distributing hot air.
The appliance is adapted to work with a hot air hose distributor up
o
100 C. The hose distributing hot air of Ø 305mm and max 15m
length shold be connected to the outlet. After connection make sure
that the hose is patent and not folded to let the air flow property.
12. Thermal circuit breaker
The appliance has been equipped with an integrated thermal circuit
breaker ensuring high safety level. The breaker will automatically
switch the power supply off once a limit temperature is exceeded.
Should it happen, let the appliance cool down and only then, look for
the reason of the problem. Next push the "RESET" button (Fig. 5)
with a pointed tip in order to unlock the thermal circuit breaker. If the
heater does not operate, contact the seller or approved service centre.
13. Out-of-season storage.
Should the appliance remain idle for a long period of time, clean
it before shoving by blowing the inside with compressed air. The
heater should be kept in a dry and clean place. Before you start using
it again make sure the power supply cable has not been damaged. In
the case of any doubts contact the seller or approved service centre.
14. Functional inspection.
The appliance should be checked at least once a year by competent
service personnel approved by the manufacturer. Any inspections
or repairs should be conducted by competent personnel only.
15. External thermostat
The appliance may work with external thermostat. In case of
propen function of external thermostat (achievement of set
temperature) it disconnect heating elements and a fan (the fan
works a switch A is set in a position nr 1 fig 3
Heating without room termostat
The unit runs under continuous duty.
- Connect the supplied bridge circuit plug 2 fig 6 to the thermostat
socket 1 fig 6 of the unit.
-Put the switches into the desired position
-WARNING!!! For optimum unit operation, the device should not be
operated at an ambient temperature above 25 °C.
Heating with room thermostat
The unit runs fully automatically and is dependent on set
temperatures.
- Remove the bridge circuit plug 2. fig 6
- Connect thermostat plug 3 fig 6 of the room thermostat (accessories)
to the thermostat socked 1. fig 6
- Put room thermostat 4. fig 6 in a suitable place. The thermostat
sensor may not be exposed directly to the hot air current and not
fixed directly on a cold surface.
- Pre-select desired room temperture on the room thermostat.
- Put the switches (fig 2,3).into the desired position.
12
.
).