Waste Disposal And Environmental Protection - IKRA HLSI 250 Instrucciones De Manejo

When the vacuum operation is selected, air and debris is
drawn up through the large vac tube, and forced through
the mulching impellor.
The debris is mulched and then blown down into the
collection bag.
Important ! Always ensure the collection bag is correctly
attached as per the "Fitting the collection bag " section
in this manual.
Always be aware of what is being drawn up into the blow/
vac tube. This product is only designed for garden debris
like leaves, twigs and garden cuttings.
Importment notes when using the blower/
vacuum selector knob (6)
Do not force the lever. The lever should move with very
little resistance. If the lever is difficult to move, disconnect
the power supply, remove the collection bag and ensure
debris, dirt or mud has not jammed the lever inside the
large round outlet.
When selecting either of the operation, ensure the selec-
tor lever is fully in one position of the other ,not half way.
Speed Controller
(Fig.15)
Produkt BVN 2500 has a adjustable speed controller and
therefore adjustable vacuuming and blowing. The speed
is fully variable from 6000 Rpm to 14000 Rpm.
To empty the collection bag
The collection bag is attached to the blower vac in 2
places. It is not necessary to remove the collection bag
from the blower vac when the bag needs to be emptied.
• The rear of the bag is fitted with a full length zip.
• Simply open the zip and empty the contents.
• Ensure to close the zip prior to operating the blower
vac.
Tips for using your blower vac
The following points may assist you in the operation of
the blower vac.
• Always try and vacuum dry leaves, cuttings or general
garden debris.
• Wet materials id difficult to mulch and also can cause
the blower vac to clog.
• If the leaves etc. are damp, then use the blower vac in
blow selection to pile the leaves etc. into one area, vac
and mulch the leaves when dry.
• Avoid using the vac on areas where there are stones,
or other hard objects. These objects will damage the
impellor of the blower vac.
• It is also advisable not to allow the blower vac to pick
up soil. Soil generally contains moisture and when
combined with other garden debris can clog the blower
vac.
• The blower vac is not a garbage disposal unit. Do not
attempt to mulch any material than general garden
debris.
• For better performance and comfort, it is recom-
mended the collection bag is emptied when it becomes
approximately half full. This reduces the weight and
also allows the vac operation to perform at its highest
level.
Maintenance and storage information
Prior to cleaning or any maintenance, always ensure the
power plug has been removed from the electrical power
supply. When you have finished using the blower vac,
always check to make sure the product is clean and free
of dirt and debris. This is important around the selector
lever flap which is just inside the round outlet. To check
this area, remove the collection bag and ensure this area
inside the outlet tube is free of debris and dirt. Operate
the selector lever backwards and forwards to ensure
correct operation.
• Do not hose or submerge any part of the blower vac.
• Do not use solvents to clean the blower vac.
• Store the blower vac in a dry place, and out of reach of
children.
Power Cord Maintenance
If the supply cord needs replacing, the task must be car-
ried out by the manufacturer, the manufacturer's
agent, or an authorised service centre in order to avoid
a safety hazard.
Troubleshooting
Attention! Always remove the plug from the
mains socket before starting any work on the
machine.
The machine won't start: Check whether the switch
•
is in the "I" position; check that the residual current
circuit breaker is not switched off and that no fuses
have blown in its electric circuit. If the machine still
won't start have it inspected by an authorised cus-
tomer service firm.
• The machine won't vacuum: Check whether the
leaf collection bag is full. If it is, empty it; check
whether the lever for the reversing flap is in the cor-
rect position, otherwise have the machine inspected
by an authorised customer service firm.
• The machine won't blow: Check whether the lever
for the reversing flap is in the correct position, other-
wise have the machine inspected by an authorised
customer service firm.
• The shredder wheel is blocked: Check whether an
object has been sucked in that is too large; a piece
of wood, cardboard or other object has become
jammed between the impeller and shredder cham-
ber. If the shredder wheel remains blocked have
the machine inspected by an authorised customer
service firm.
• If the machine vibrates, please immediately stop us-
ing it. Have the machine inspected by an authorised
customer service firm.

Waste disposal and environmental protection

If your device should become useless somewhere in the
future or you do not need it any longer, do not dispose
GB-6