Safety Instructions; Intended Use - Kaiser RB 520 AS Instrucciones De Manejo

5279Bedien_0819.qxp_5279Bedien 28.10.19 09:44 Seite 5
ENGLISH
(1) Light
(2) Vertical arm
(3) Articulated joint base
(4) Soft screen
(5) Mains adapter
(6) Mains lead
(7) Fastening screw for vertical arm
(8) A8.4 washer
(9) Fastening screw for mounting the articulated joint
base to a Copylizer
(10) M8x16 hexagon socket screw
(11) ø 32 mm washer for mounting the articulated joint
base to a shooting table
(12) Fastening screw for the light
(13) Extension cable
(14) Cable clip
(15) Control dial for brightness and ON/OFF
(16) Display
(17) Light synchro cable
(18) Latch release
(19) Plug of light synchro cable
(20) Port for light synchro cable
(21) Port for power supply
(22) Locking screw for the light
(23) Splitter cable
(24) Control LED
Prior to using your RB 520 AS surface lighting unit, please
read these instructions carefully. Keep them safe to have
them at hand at any time. If you pass the devices on to
somebody else, always include these instructions.

1. Intended use

The RB 520 AS surface lighting unit is marketed exclusively
for the purpose of illumination for image capture. It is not
intended for household lighting.
The lighting unit is equipped with articulated joint bases for
attachment to the exe.cutive LED Copylizer (5215), the
exe.cutive LED Illumina Base Plate (5244) or the TopTable
PRO Basic Support (5921). Supplemented with the 5256
Clamp Bases – available as an accessory – it can also be
attached to boards up to 48 mm (1.9 in.) thickness.
Use the RB 520 AS surface lighting unit only as described
in these instructions. Any other use has to be considered
as not as intended and can result in material damage or
physical injury. The RB 520 AS surface lighting unit is not
a toy.
Kaiser takes no responsibility for damages caused by not
intended or incorrect use.

2. Safety instructions

Please observe the following safety instructions:
WARNING!
Disconnect the devices (lights / mains adapter) from the
mains if not in use or before cleaning.
Keep the products away from children.
Do not put the devices into operation, if housing, plugs or
cables are damaged.
Do not disassemble or modify the devices. Repairs must
only be carried out by qualified persons.
CAUTION!
Only use the lighting unit with parts designed for it.
Use the devices only in dry rooms.
Keep the devices away from water and other liquids and
from combustible materials.
Make sure that the devices are not covered during opera-
tion.
Do not use or store the devices at places with extremely
high air humidity or at extremely hot places. Keep the de-
vices away from direct solar radiation.
Let the devices cool down before boxing them.
3. Check devices and scope of supply
When unpacking the devices for the first time, please
check if the scope of supply is complete. It comprises
2 Lights (1) with soft screen (4)
2 Fastening screws (12) for the lights
2 Vertical arms (2)
1 Accessory kit:
2 Articulated joint bases (3)
4 M8x16 hexagon socket screws (10)
(for mounting to a Copylizer only 2 screws are
necessary)
2 A8.4 washers (8)
4 ø 32 mm washers (11) (for mounting to the
TopTable PRO basic support)
1 Hex-wrench SW6 (6 mm)
2 Fastening screws (9) (for mounting to a
Copylizer)
2 Fastening screws (7) for vertical arms
4 A8.4 washers (8)
1 Mains adapter (5)
1 Mains lead (6)
1 Splitter cable (23)
2 Extension cables (13)
1 Light synchro cable (17)
4 Cable clips (14)
Check also, if the devices are damaged by extraneous
causes. If this is the case, do not take the devices into op-
eration.
4. Assembly / Connecting the mains adapter
Attach the articulated joint bases (3) and the vertical arms
(2) as shown in fig. C or D:
fig. C shows mounting it to a Copylizer or
to a illumina base plate,