Dörr EcoLine II Serie Manual De Instrucciones página 10

05 | INSTALLATION
05.1 Installation of the modelling light
CAUTION
In order to avoid burns, cool down the studio fl ash before replacing the modelling light!
CAUTION
Do not touch the modelling light and the fl ash tube with bare hands.
Greasy fi ngerprints may cause the bursting of the lamps during
operation! Wear thin gloves (special microfi ber cloth available
from DÖRR) or use a cloth for inserting or replacing the lamps.
1. Make sure to switch off the studio flash with the main switch (5) and to disconnect
from main power supply.
2. Insert the long plug-in contacts of the modelling light (20) into the 2 holes of the
modelling light socket (18) and gently push the modelling light down.
CAUTION
The modelling light is only designed to illuminate the object while the camera settings are
made. It is not suited as a permanent light since it produces high temperatures which can
harm fl ash accessories. In combination with conical snoots, softboxes, honey combs or other
fl ash accessories the modelling light must not be used for more than 10 minutes.
05.2 Mounting onto a light stand
Suitable light stands optionally available from DÖRR or included in your kit.
Put the tripod socket (12) over the spigot of your light stand and fi x the locking screw
(13). To adjust the tilt angle, loosen the locking screw (14), adjust to the desired angle and
tighten the locking screw (14) afterwards.
CAUTION
Make sure that the studio fl ash is mounted stable and secure and cannot tip over. Risk of fi re!
Take care that that nobody stumbles over the cable connections.
05.3 Connecting to the camera
Plug the 3,5mm jack of the sync cord (21) into the socket (6) of studio fl ash. Insert the sync
plug of cord into the sync socket of your camera. If your camera is not equipped with a
sync socket, please contact your specialized retailer for the purchase of an optional fl ash
sync adapter (available from DÖRR).
05.4 Power connection
Connect the power cable (7) to the main power supply and switch on the studio fl ash with
the main switch (5) (position I = ON).
05.5 Test button
By pressing the test button (9), the studio fl ash is triggered manually e.g. to check the
proper function of the studio fl ash or to give o excess energy after reducing the fl ash
power (see also chapter 06, point 3 'Please note').
06 | STUDIO FLASH PHOTOGRAPHY
CAUTION
While operation never touch the ignition wire, the fl ash tube, the modelling light and the
refl ector – risk of burns and of electric shock! Never cover the ventilation slots.
1. Switch on the studio flash with the main switch (5). Set your camera to program mode
M for manual settings (for details see the instruction manual of your camera).
2. Set the correct exposure time according to your camera's instruction manual. We
suggest to set the camera to an exposure of 1/125s or 1/60s.
3. For an optimum exposure, we recommend to test various aperture settings (for details
see the instruction manual of your camera) and to vary the flash power. The flash
power can be adjusted variably from 1/16 to full power by turning the power control
(11) of studio flash. We recommend starting with a medium aperture (e.g. 8) and a low
flash power.
Please note:
After reducing the fl ash power, you must give o excess energy left in the fl ash condenser
in order to avoid an overexposure of the subsequent picture. To do so, you have to press
the test button (9) once or release the fl ash e.g. with a wireless fl ash trigger (optionally
available from DÖRR).
Note
For quick and proper determination of the correct aperture setting, we recommend to use
a fl ash exposure meter (optionally).
06.1 Modelling light
The modelling light (20) assists you in fi nding out the correct illumination. It does not in-
fl uence the fi nal illumination while shooting. To save energy and in order to avoid overhe-
ating, please switch o the modelling light after your test shootings (On/O switch (10)
to O position = O ).
CAUTION
The modelling light (20) assists you in fi nding out the correct illumination. It does not infl u-
ence the fi nal illumination while shooting. To save energy and in order to avoid overheating,
please switch o the modelling light after your test shootings (On/O switch (10) to O position
= O ).
06.2 Photocell (Slave)
The incorporated photocell (1) allows simultaneous triggering of the studio fl ash with a
main fl ash, e.g. a system fl ash unit (see chapter 07).
Kindly note that the photocell reacts on great di erences in brightness. In case that the
photocell is exposed to intensive light like e.g. strong sunlight, the function of photocell
may be limited as the photocell is not able to detect a su cient di erence in brightness
anymore.
Please take care that the photocell is not covered by a softbox or other accessories.
In order to prevent undesired fl ashes released by photocell (e.g. triggered by another
photographer), cover the photocell with the shielding cap (2).
CAUTION
Switch o the studio fl ash with the main switch (5) after each usage.
10