Proper Use; Technical Data - EINHELL TC-PT 2500 S Manual De Instrucciones Original

3. Proper use

The equipment is designed for transporting goods
on pallets with an open base or with stringer
boards extending beyond the load wheels. The
equipment must be used on a fi rm, fl at surface.
It is prohibited to use the equipment to pick up or
transport people.
The built-in weigher enables you to weigh the
moving loads. The weigher is not calibrated and is
not capable of calibration.
Ambient temperature of 0°C - +40°C.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.

4. Technical data

Overall height: ...................................... 1220 mm
Overall length: ...................................... 1540 mm
Fork length: .......................................... 1150 mm
Fork height min.: ....................................... 85 mm
Fork height max.: .................................... 200 mm
Fork width single: ................................... 160 mm
Fork width total: ...................................... 540 mm
Lift max.: ................................................ 115 mm
Load: ........................................................2500 kg
Weight approx.: ...........................................66 kg
Steering wheels Ø: ................................. 200 mm
Load-bearing rollers Ø: ............................. 80 mm
Weighing range: ........................... 200 – 2500 kg
Scale graduation: ........................................20 kg
Measurement tolerance of the total
measuring range: .......... ........................... +/- 2%
5. Assembly
Note: The hydraulic system is secured with a bolt
(M). Do not remove it until prompted in the fol-
lowing assembly description and keep it in a safe
place for future maintenance work.
Anl_TC_PT_2500_S_SPK7.indb 12 Anl_TC_PT_2500_S_SPK7.indb 12
GB
1. (Fig. 1) Press down the control lever (2) as far
as it will go into the lowering position (see 6.
Operation).
2. (Fig. 2) Pass the control chain (F) through
and out of the recess at the bottom end of the
drawbar. Insert the bolt (B) through the hole
in the drawbar mount (C) and the hole in the
drawbar.
3. (Fig. 3) Make sure that the clamping sleeve
passage (E) coincides with the clamping
sleeve hole in the bolt (B).
4. (Fig. 3) Pass the control chain (F) through the
hole in the bolt (B) so that the hydraulics sys-
tem works.
5. (Fig. 3) Press the drawbar (3) down a little so
that the hydraulics lock bolt (M) is slackened
and can be removed.
6. (Fig. 4) Hook the setting screw (H) with the
pre-mounted hex nut (K) into the hydraulics
lever (L).
7. (Fig. 5) Check whether the clamping slee-
ve mount of the bolt (B) coincides with the
clamping sleeve passage (E) in the drawbar
mount. Use a hammer to tap the sleeve (A)
into the bolt (B).
Note: The equipment can be optionally equipped
with a foot-activated parking brake. If required,
please contact your customer service team.
Operating the foot-activated parking brake:
Push the brake to the right as far as the stop – the
wheels will be blocked.
Push the brake to the left – the wheels will be
released again.
6. Functions
Important! Note the safety information (section 1.)
and Figure 7.
On the drawbar is a sticker showing the positions
of the handle switch (Fig. 6).
1 = Lower (lowering position)
2 = Travel (traveling position)
3 = Lift (lifting position)
The pallet lifting truck is allowed to be parked only
when the lifting forks are lowered.
The following functions are possible and were
already set in the factory.
- 12 -
19.08.15 10:06 19.08.15 10:06