Exhaust Air Connection - Bosch Nexxt WTMC3300US/01 Operacion, Cuidado E Instrucciones Para La Instalacion

10. Checkthe U,L strainrelief
clampto makesurethatit is
tight andcannotbe turned.
11. Replacethecoveron the
terminal b lockandfastenin
place,
[_ Makesurethatthe U.L.strain
reliefclampis outsidethe
cover!
Theappliance is nowreadyto be
pluggedintotile 4-wirereceptacle
ofthe powerrating.
Connecting 3-wire power supply
cord
1.Remove the screwsfromthe
coverof theterminal b lock
Ioca[edat[he top rearof [he
appliance.
2. Makesure[hatthereis
a groundingstrap.
3. Fixthe strainreliefclampto the
anglebracket.Tightenthe nut.
4. Loosenthe 2 screwslabeled L
andthe screwlabeled N in the
terminal b lock.
5. Threadthe 3-wirecable
throughthe U,L.strainrelief
clamp,
6. Tightenthe screws(2.5 Nm)on
the U.L strainreliefclampso
thatthe powercord cannotbe
moved,
7. AtIachthe 2 powercordouter
conductors(redandblack)to
the 2 terminals labeledL and
the remaining powercord
conductor(white) t o [he
terminal l abeledN.
8. Tightenall3 screws(3 Nm)so
thatthe powerconducIorsare
heldin placesecurely,
9. Checkthe U.L.strainrelief
clampto makesurethat it is
tight andcannotbeturned.
10. Replace the coveron the
[erminal b lockandfastenin
place,
[_ Makesurethai the U.L.strain
reliefclampis outside[he
cover!
Additional grounding procedure
Somelocalregulations may
requirea separate ground.
tnsuchcases,the required
accessory groundwire,clamp
andscrewmustbe purchased
separately.
Nevergroundthedryerto
plasticplumbing lines,gas lines
or waterpipes.
Groundinginstruction
Thisappliancemustbe grounded.
in [he even[ofa malfunction or
breakdown, g roundingwill reduce
the riskof electricshockby
providing a pathof leas[resistance
forthe elec[riccurrent.
ForCanada[he dryercomeswi[ha
cordwhbh hasanequipment
groundingconduc[oranda
groundingplug.Theplug mustbe
pluggedintoan appropnate outlet
whichhasbeenproperlyins[ailed
andgroundedinaccordance wi[h
alllocalregulations andordinances.
Improper c onnectionof the
equipmentgroundingconductor
mayresultinebctricshock,
Havethe appliancecheckedby
a qualified electrician or service
technicianifyouarein doubtas
to whether the dryerhasbeen
properlygrounded,
Exhaust air connection
1. To reduce the risk of fire, this
dryer MUST BE EXHAUSTED
OUTDOORS.
2. To reduce the risk of fire, do
not use the ductwork longer
than recommended.
3. DO NOT use a plastic or
non-metal duct with this dryer,
4. DO NOT use a duct smaller
than 4 inches in diameter,
5. DO NOT use exhaust hoods
with magnetic latches.
6. DO NOT exhaust the dryer into
a chimney, furnace cold air
duc[, attic, crawl space, or any
other ductwork used for
venting.
7. DO NOT install a flexible duc[
in an enclosed wall, ceiling or
floor.
8. DO NOT crush or kink the
duct.
9. Do clean and inspect the
exhaust system on a regular
basis; at least once a year.
10. The exhaust duct must
terminate in a manner to
prevent back drafts or entry of
birds or other wildlife,
The Bosch dryers are intended to
be vented outdoors, To prevent
build-up of moisture and
accumulation of lint indoors, as well
as to main[ain maximum drying
efficiency, it is recommended that
the dryer is vented outdoors.
Exhaust air outlet on the dryer
The dryer is delivered with an
exhaust air outlet on the rear of the
appliance.
To take account of the spatial
requirements and an exis[ing
exhaust air system, the following
connection options are possible for
the exhaust air outlet:
- on right side of [he appliance,
- on the underside of the
appliance,
9