GE GXCC01D Serie Manual Del Propietário página 7

To remove To replace
_ Supportcollar
Separator
Cleaning the Separator
IMPORTANT: Set both power switches (on the
back of the dispenser) in the 0 (off) position
and unplug the water dispenser before
cleaning.
1. ReIIlO\r( |he _r_l_ _"t_l]_ _t drain the
dist)enser (see Draining the Dispenser).
2. I_elIlo\re |he supporl collar 1)} turning
com_terclockwise and pulling straight DiE
3. Remove tile plastic separator t)y pulling
straight out (}u)u Ina} need to |\vis[
slightly to loosen).
4. Clean the separator Mtb dish soap
and water or ill the top rack of the
dishwasher,
5. Dry the separator tllorougbly on
both sides.
6. Using a clean clottl or paper towel,
thoroughly dry the cold water reserv()il:
7. Place the separator back ill the (list)easel:
Make sure the long, mt)ered end of the
set)arator is positioned tirml} on the
metal plug on tlle botlonl of tile
r('s('rvoil:
8. Retllace the SOl)port collar and turn
clock'wise (mtil it is firmly ill t)lace,
9. Install a flfll water bottle on the dispenser
(see Loading the Dispenser).
Sanitizing and Cleaning the Water Tanks
IMPORTANT" Periodicallythe water dispensertanks mustbe sanitizedto prevent unpleasanttastes in the water and cleanedto
removemineralde )ositsthat can impairflow
ToSanitize:
1. B(f()re
cleanii/g, sei
bolh
l)o_ver swilcb(!s
(on lhe back of dw disi)enser ) ill Ihe O (off)
U
i)osidon aI/d enpIeg the water dispenser. OFF
NOTE: For firsl lira( inslal]ali(m, skip position
steps 2-4.
2. Empb, tile waI(r l/otde, then remov( it l]'om tile
disi)enser.
3. Drain tb( water tanks (see Draining No Dispenser).
4. Reinstall the silicon stopper and drain cap (on floor
models) or the drain cover and retaining clip (on
coentertop models) (see Draining the Dispenser).
5. DO NOT ADD BLEACH FIRST OR DIRECTLY TO THE
DISPENSER. Concentrated hleach may damage plastic.
Add 1/2 te_tspoon (2.5 ml) ofordiimry 6.0%
//laXillllllll household blea(h to a 2 (llmrt (2 liter)
I)itch(r filled with tap water.
6. Pour tile solution ill tim opening at th( top of
tb( dispenser.
7. Repeat steps 5 and 6 imtil tile dispenser is fllll.
8. Press tile hot and cold dispenser butIons imtil the
water jllst begins to flow/i'om the tai)s.
9. Allow to sit/i/r 15-20 n/inures.
10. Rinse pet the bleach soletiom
-- Drain the \\rHl('r tanks into a l_u'gc bll(k('t
(floor models) or sink (count(rto t) models)
(see Draining the Dispenser).
-- ]X,'/_ke sm'e that the silicon stopper (/lear
models) or drain cov(r (colmtertop models)
is NOT installed.
-- IMPORTANT? Remove the separator and wipe oct the
cold water reserve# (see Cleaning the Separator).
-- (]lean, then rcinst_lll tb(' SCl/arator _md collar
(see Cleaning the Separator).
-- Pore- N)t)roxim_mqy 1 gallon (4 qlmrts or
4 lilers) ofli'csh tap \*,r}lt{'rinto the top _md allow
to drain in[o tile bucket (floor rood(Is) or sink
((ounterto I) models).
-- Fh/sb with all additional 1 gallon (4 qmu'ts or
4 liters) ofli'esh tap water and allow to drain
lille the buckel (floor models) or sink
((ountertop models).
11. Reinstall the silicon stopper and drain cap (on floor
models) or the drain cover and retaining clip (on
coentettop models) (s(( Draining the Dispenser).
12. install a/i'(sh \\rater berth' (see Loading the Dispenser).
13. Dispense 1 quart (1 fiter) of water from each tap
and taste to m_&e sm'c the l/lc_tch solmion is
complelely removed.
If Foe continue to taste the chlorine from the bleach soletion,
repeat steps 10-13 enti] the taste is gone.
14. Phlg ill Ill( dispenser. Then Illrn Oil |tl( tl()|
[_
and cold l)()wer s_xiI(ll(?s
(Oil
Ill(! ba(k of Ihe
disI)ens( r)" ON
position
To Remove Mineral Deposits:
Mix 2 quarts (2 liters) of water with two quarts of vinegar OR mix I gallon of water (4 liters) with 16 ounces (454 g) of citric acid
crystals, Bleach does not remove mineral deposits, Do this in place of step 5 when removing mineral deposits,