Publicidad
Idiomas disponibles
Idiomas disponibles
(96) Left pedal post.
(102) Right pedal post.
(104) Left pedal.
(105) Right pedal.
(106) Left connection tube.
(108) Right connection tube.
(110) Cushion plate.
(111) Left swing post.
(112) Right swing post.
(113) Console.
(116) Bottle holder.
(117) Adaptor.
Fig.2 Fasteneers List:
(124) Screw M8x40
(125) Self-locking nut. M8
(126) Screw ST3x10
(127) Hex Screw.
(128) Screw M8x20
(129) Spring washer D8x15
(132A) Screw M10x60
(133A) Self-locking nut. M10
(134) Screw M5x16
(135) Screw M10x50
(136) Screw M8x15
(137) Screw M8x25
(141) Curved washer
158) Washer
(
(159) Washer
2.
FITTING THE LOWER TUBES.-
ATTENTION: The assistance of a second person is
required for this stage of the assembly.
Bring the left connection tube (106) to the main body
(1), and place it according to figure Fig.3, Insert screws
(127) and tighten securely.
Perform the same assembly with the right hand and the
right connection tube (108).
3.-
FITTING THE ADJUSTABLE FEET.
Take the left pedal tube (96) marked with the letter (L),
place the cushion plate (110) as shown in Figure 4.
Then place the left pedal (104) and secure with screws
(134).
Perform the same assembly with the right footrest
assembly (102) marked with the letter (R) and the right
pedal (105) Fig.4.
4.-
FITTING THE REAR STABILISER.
Move the upper part of the left pedal tube (96) to the
arm of the central body (1), insert it into the arm as
sohwn in Fig.5. Place the bushings (144), Fig.5, and
tighten them securely.
Then close the bottom part of the left pedal tube (96) to
the regulatory arm of the central body (1), and insert it
into the arm Fig.5A.
Place the screws (132A), together with the washers
(158), (159)
and (133A) and tighten securely.
Perform the same steps of the right pedal tube
assembly (102).
5.-
FITTING THE FOOT REST FOCUS
BARS.-
Bring the
handle left connection tube
body (1), placing it according to the Fig.6. Insert screws
(137) with washers (129) and screws (135) on the back
joining with
left connection tube
tighten securely. Perform the same steps with the
handle right connection tube.
6.-
FITTING THE SWING POSTS.-
Move the
left swing post
main body (1), Fig.7.and inser it. Fix with screws (124)
together with nylon nuts (125) and washers (141) Fig.7
and tighten securely. Perform the same with your right
hand and
right swing post
covers of the swing posts (92) and (94) and the rear
covers (93) and (95) as shown in Fig 8.and screw them
with the screws (126).
7.-
FITTING THE MONITOR POST.-
Place the post (79) and move it near the main body (1)
as shown in Figure 9. Insert the wire from main body
(1) through the slot of the post (79) as shown in Figure
9 and tighten the post with the screws (128).
8.-
FITTING THE FIXED HANDLES.-
Place screws (136) firstly.
Place the
left fixed handle bar
letter L) and insert it into the external part of the man
body (1) Fig.10, taking special acoount to insert wires
handgrip and taking them through the slot where the
monitor will be placed as shown in details figure
Loosen
the screws (136) with the handle (90)
positioned to hold it firmly.
Perform the same asembly with the right hand and the
handlebar (85).
IMPORTANT: It is advisable to retighten these
screws after one month of using the machine.
9.-
FITTING THE MONITOR.-
Attach the bracket (115) on the support plate monitor
(114) with screws (138) and fix the monitor (113) as
shown in detail in Figure 11 with screws (138)
introducing previously the monitor wires by the support
(114).
Bring the monitor (113) to the monitor post (79) and
connect the wires. Place the monitor (113) onto the
plate of the monitor post (79), as shown in Fig.11 being
careful not to pinch the cables. Fix the monitor with the
supplied screws (139) Fig.11.
Then place the bottom cover (84) of the monitor as
shown in Figure 12.
LEVELLING.-
Once the unit has been placed into its final position,
make sure that it sits flat on the floor and that it is level.
This can be achieved by screwing the adjustable feet
(49) up or down, as shown in Fig.13.
16
G818BM
(82) to the central
(106) after aligning and
(83).
(111) to the outer tube on the
(112). Then place the frontal
(90) (marked with the
10.
Publicidad
