Sony Trinition PVM-20S1WE Manual De Instrucciones página 13

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

6a USER CONFIG 1 menu
Select an item to adjust on the menus and screens (!™
through !•). To go to the USER CONFIG 2 menu,
select NEXT PAGE.
6b USER CONFIG 2 menu
Select an item to adjust on the menus (!ª through @£).
To go to the USER CONFIG 1 menu select
PREVIOUS PAGE.
7AUTO ADJUST screen
Select the color bar signal (full, SMPTE, EIA) and
press ENTER/SELECT to start automatic "chroma"
and "phase" (NTSC signal only) adjustments.
To activate these adjustments, select ON on the
CHROMA SET UP menu (3).
8ADJUST GAIN screen
Adjust GAIN in USER mode.
9ADJUST BIAS screen
Adjust BIAS in USER mode.
!ºCOLOR TEMP RANGE menu
Select the color temperature range in USER mode.
!¡USER COPY menu
Store the factory setting of D65 or D93 as the value for
USER mode.
!™COLOR SYSTEM DISPLAY menu
Select the color system type. When AUTO is selected,
the color system type being used appears on the screen
each time you change the signal input.
!£SUB CONTROL menu
Select an item (CONTRAST, BRIGHT, CHROMA
and PHASE controls on the front panel) to finely
adjust on the SUB CONTROL screen (!¢).
!¢SUB CONTROL screen
Finely adjust the selected item on the SUB CONTROL
menu (!£). Each control (CONTRAST, BRIGHT,
CHROMA and PHASE control) has a click position at
the center of its adjustment range. You can adjust the
setting of the click position with this feature.
!∞USER PRESET menu
If you select ON on this menu, the REMOTE indicator
lights up and the controls on the front panel do not
work. The monitor operates with the user preset
settings.
To adjust the user preset settings, select the PRESET
ADJUST menu (!§).
!§PRESET ADJUST menu
You can preset the BRIGHT, CHROMA, PHASE,
CONTRAST, VOLUME, and APERTURE controls to
a desired level and can use these settings by selecting
ON on the USER PRESET menu (!∞).
!¶PRESET ADJUST screen
Adjust the selected item (BRIGHT, CHROMA,
PHASE, CONTRAST, VOLUME, and APERTURE
control) on the PRESET ADJUST menu (!§).
!•V HOLD screen
Adjust the vertical hold if the picture rolls vertically.
When you cannot read the display, select the input that
is not connected.
!ªCOMPONENT LEVEL menu
[5000K–10000K]
Select the component level from among three modes.
N10/SMPTE
BETA 7.5
BETA 0
@ºNTSC SETUP LEVEL menu
Select the NTSC setup level from two modes.
The 7.5 setup level is mainly used in north America.
[AUTO]
The 0 setup level is mainly used in Europe.
[0]
@¡ACC menu
Set ACC (Auto Color Control) circuit on or off. When
the fine adjustment is necessary, select OFF on the
ACC menu.
Normally select ON.
@™LANGUAGE menu
You can select the menu language from among five
languages (English, German, French, Italian, Spanish).
@£DEGAUSS DELAY menu
Set the time for the degauss delay function to work
after the power is turned on.
This function can be set at 0 to 99 seconds.
for 100/0/100/0 signal
for 100/7.5/75/7.5 signal
for 100/0/75/0 signal
[N10/SMPTE]
[OFF]
[ON]
[ENGLISH]
13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Trinition pvm 20s1wuTrinition pvm-20s1wa

Tabla de contenido