Unpacking The Device; Putting Into Service - AEG VL 5530 S Instrucciones De Servicio

English
24
Any other use of this device is considered to be contrary
to the intended use and may result in damage to materi-
als or even personal injury.
The fi rm ETV - Elektro-Technische Vertriebsgesellschaft
mbH does not accept any liability for damage caused as
a result of the use of this device contrary to its intended
use.

Unpacking the Device

• Remove the device from its packaging.
• Remove all of the packaging material such as foils,
fi lling material, cable holders and cardboard packag-
ing.
• Check the scope of delivery.
NOTE:
There may still be dust or production residues on the
surface of the device. We recommend that you quickly
wipe off the housing with a damp cloth.
Assembly instructions
The device must be completely assembled before use!
While reading the text it is advisable to refer to the
„Overview of the Components".
1. Place the parts of the base together in the shape of a
cross.
2. Screw the mounting plate (15) tightly to the base.
Four crosshead screws are included in the scope of
delivery.
3. Push the covering cap (14) on to the lowest position
of the upright tube (13).
4. Loosen the connection screw (11) and insert the gear
casing (10) and the motor casing (9) on the stand
tube. Then tighten the screw well.
5. Position the rear protection grid (7) in place in accor-
dance with the recesses.
NOTE:
Please ensure that the carrying handle is facing
upwards.
6. Turn the attachment ring (6) for the rear protection
grid (7) slightly in a clockwise direction.
7. Attach the propeller. Note the position of the guide
pin on the motor shaft.
8. Tighten the attachment screw (4) for the propeller in
an anticlockwise direction.
9. Insert the front protective grille (1).
NOTE:
Ensure that the holes for the attachment screw in
the front and rear protective grille are aligned one
above the other.
10. Tighten the protective grille with the attachment
screw supplied.
11. Close the attachment hooks.
05-VL 5530 S AEG.indd 24 05-VL 5530 S AEG.indd 24
Position
The ideal position is a non-slip, fl at surface.

Putting into Service

Electrical Connection
1. Before inserting the plug into the socket. Make sure
that the mains voltage to be used matches that of
the device. You can fi nd this information on the
nameplate.
2. Connect the device to a duly installed 230V/50Hz
protective contact socket. The control lamp POWER
now illuminates.
Remote Control
• The cordless remote control has a range of up to 6
meters.
• When using the remote control, please ensure that
there are no obstacles placed between it and the sen-
sor on the device.
• If this range becomes smaller the batteries need
replacing.
Inserting Batteries into the Remote Control
(Batteries not supplied)
• Open the lid of the battery compartment on the rear
of the remote control.
• Insert 2 MICRO batteries of type R03 „AAA" 1.5 V.
• Please ensure the correct polarity. Information is
shown on the remote control itself.
• Close the battery compartment.
NOTE:
• The buttons marked with an * are located on the
device and on the remote control.
• If you are not going to use the remote control for
a prolonged period, please remove the batteries in
order to prevent them from leaking.
CAUTION:
• Used batteries should not be disposed of in the do-
mestic waste. Please return all batteries to a special
collection point. Your local authority will provide
you with information on this.
• Diff erent types of battery or new and used batte-
ries must not be used together.
Use
Basic Settings
Set the blower inclination angle before starting the
device. You can adjust the inclination angle by tipping
the blower casing with both hands.
CAUTION:
The inclination angle amounts to approx. 15°.
05.11.2008 9:19:49 Uhr 05.11.2008 9:19:49 Uhr