GBC HeatSeal H212 Manual De Instrucciones página 5

Important: Before operating your new laminator, lift up the exit tray located at the rear of the machine and lock it in place (fig. 1).
Operation, hot lamination
Connect power cord to appropriate power source.
1
Push the power button to turn the power "ON" (fig. 2). The
2
indicator will glow red.
Using the lamination guidelines (fig. 3), select the appropriate
3
temperature setting for the pouch gauge thickness and material you
are laminating.
• If the laminated item appears to be cloudy, it means that the
laminator temperature is not hot enough. Allow the laminator to
heat for a few more minutes then run the pouch through again.
• If the laminated item is wavy, the TEMPERATURE is too hot. Verify
temperature selector is set at the appropriate temperature.
• Always allow sufficient time for the laminator to adjust to changes
in temperature setting.
Operation, cold lamination
Connect power cord to appropriate power source.
1
Rotate the temperature dial to the "cold" position (fig. 2).
2
Push the power button to turn the power "ON" (fig. 2), the
3
indicator light will glow red.
Release lever
How to use the release lever.
If pouch jams or is fed improperly, turn off the laminator immediately.
1
Press the release lever down to release the motor from the rollers
2
(fig. 6).
Pull your document back out of the laminator while pressing the
3
release lever down (fig. 7).
Helpful lamination hints
Temperature setting Guidelines:
1
When laminating thin paper with light ink coverage, set the
temperature dial at the low end of the range. Thick paper and heavy
ink coverage require higher settings. Temperature settings will vary
due to the finish, chemistry and heat absorption properties of the
material being laminated.
Before laminating important or unique documents always run a test
2
pouch through the laminator using a similar type document.
Guarantee
Operation of this machine is guaranteed for two years from date of
purchase, subject to normal use. Within the guarantee period, ACCO
Brands Europe will at its own discretion either repair or replace the
defective machine free of charge. Defects due to misuse or use for
inappropriate purposes are not covered under the guarantee. Proof
of date of purchase will be required. Repairs or alterations made by
Register this product online at www.accoeurope.com
A series of four beeps will be heard when laminator reaches
4
operating temperature.
Position the document to be laminated into a GBC laminating pouch,
5
so that the document is aligned to the folded sealed edge and the
right and left borders are equal (fig. 4).
Insert the pouch and its contents straight into the machine, leading
6
with the folded edge.
The laminated item will automatically exit the rear of the machine.
7
After the pouch has stopped moving, immediately place it on a flat
surface to cool for one minute before handling (fig. 5).
8 If you have finished laminating, push the switch to turn "OFF" the
machine.
DO NOT LAMINATE AN EMPTY POUCH
A series of four beeps will be heard when the laminator is ready to
4
use.
5 Use and laminate your GBC cold pouch.
(Pressure sensitive—non-thermal laminating pouch)
Clean the rollers by running the cleaning sheet supplied with the
4
laminator through the machine 2 or 3 times in the hot operation
mode (red zone on temperature dial). If you do not have this sheet,
use a similar cardboard sheet that fits the width of the laminator.
Continue laminating.
5
Do not attempt to do single sided lamination. This will destroy the
3
laminator.
As soon as the lamination is completed, remove from the rear of the
4
machine and place on a cool flat surface for cooling to prevent the
pouch from curling.
Do not block the vent slots, this will cause the laminator to overheat.
5
persons not authorised by ACCO Brands Europe will invalidate the
guarantee. It is our aim to ensure that our products perform to the
specifications stated. This guarantee does not affect the legal rights
which consumers have under applicable national legislation governing
the sale of goods.
G