Functional Description; Intended Use; Product Features; Noise/Vibration Information - DIAM MEA125 Manual De Instrucciones

Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when the
cable is damaged while working. Damaged cables increase
the risk of an electric shock.

2. Functional Description

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or
serious injury.

2.1. Intended Use

The machine is intended for cutting, roughing, and brushing
metal and stone materials without using water.
With approved sanding tools, the machine can be used for
sanding with sanding discs.

2.2. Product Features

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Release screw for protection guard
2 Spindle lock button
3 On/Off switch
4 Auxiliary handle
5 Grinder spindle
6 Protection guard for sanding
7 Mounting flange
8 Grinding/cutting disc
9 Clamping nut

2.3. Noise/Vibration Information

We reserve the right to undertake modifications to reflect
technical advances.
D = maximum grinding disc diameter
max
n = no-load speed
M = spindle thread
P = rated input
1
a = typically rated acceleration in the hand-arm area
hw
Typical A-rated acoustic level:
L =acoustic pressure level
PA
L = acoustic power level
WA
During peration, the acoustic level may exceed 88 dB(A).
Wear ear protectors!
m = Mass
Measures values established according to EN 60745.
The stated technical specfications are subject to tolerances
(as specified in the respective current standarsd.)

2.4. Declaration of Conformity

We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with the
following standards or standardization documents:
ENGLISH
EN 60745-1, EN 60745-2-3, EN 55014-1, EN 55014-2, EN
61000-3-2, EN 61000-3-3 according to the provisions of the
directives 2006/42/CE, 2014/30/EU,2011/65/EU.
3. Assembly
3.1. Mounting the Protective Devices
Before any work on the machine itself, pull the
mains plug.
Protection Guard for Sanding
Place the protection guard 6 onto the spindle collar of the
machine until the encoding keys of the protection guard
agree with the spindle collar. Press and hold the release
screw 1 while doing this.
Adjust the position of the protection guard 6 to the
requirements of the work process. For this, release screw 1
upward and turn the protection guard 6 to the required
position.
Adjust the protection guard 6 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 6 may be turned only upon actuation
of the release screw 1! Otherwise the power tool may not
continue to be used under any circumstances and must be
taken to an after-sales service agent.
Auxiliary Handle
Operate your machine only with the auxiliary handle 4.
Screw the auxiliary handle 4 on the right or left of the
machine head depending on the working method.
3.2. Mounting the Grinding Tools
Before any work on the machine itself, pull the
mains plug.
Grinding and cutting discs become very hot while
working; do not touch until they have cooled.
Clean the grinder spindle 5 and all parts to be mounted.
For clamping and loosening the grinding tools, lock the
grinder spindle with the spindle lock button 2.
Actuate the spindle lock button only when the grinder
spindle is at a standstill. Otherwise, the machine may
become damaged.
Grinding/Cutting Disc
Pay attention to the dimensions of the grinding tools. The
mounting hole diameter must fit the mounting flange
without play. Do not use reducers or adapters.
When using diamond cutting discs, pay attention that the
direction-of-rotation arrow on the diamond cutting disc and
18
September 2017