Audizio 102.237 Manual De Instrucciones página 12

•
Add / Remove AP
Add AP - It will scan out a list of routers around.
Add AP (WPS button) - Choose this option to connect your Wi-Fi router via WPS if the router has a WPS button.
Remove AP - If you have already added a router and want to remove it, choose this option.
Note: Always bring the radio within 2 meters of the Wi-Fi router for setup.
•
AP
If you have added more than one routers on the radio and want to switch to another one, select this option to
change.
•
Signal
This is to show the strength of the Wi-Fi Signal of the Wi-Fi router as received by the radio. Usually signal levels
lower than -70dBm is at weaker level and if it affects the reception of your radio, you may need to optimize the
router location or check any problem of the router itself.
•
IP
The IP is set Dynamic by default. Select to change Fixed IP according to your network condition.
•
DNS
The DNS is set Dynamic by default. Select to change <Fixed> DNS according to your network condition.
LAN Network
Connect the Tuner's Ethernet port to one of the LAN ports in a router or Wi-Fi router using CAT 5 or CAT 6 cable. If your Router
or Wi-Fi router is DHCP-enabled (recommended), you don't have anything to setup and the Tuner will connect to Internet with
the parameters automatically assigned by the Router/Wi-Fi router.
Use the remote control for configuration if you want to use a fixed IP, scroll to IP:[Dynamic] and press [OK]. Choose Fixed.
Press the [▲] button, you can then enter the IP, press [▲ / ▼] to tune to the required numbers: xxx.xxx.xxx.xxx. Switch among
the 4 groups by pressing [◄ / ►]. When done, press OK. Scroll to GW and NM to do the same. You can also choose to use a
DNS server other than the one from the DHCP server. Scroll to DNS and do the same.
Note: Use DHCP to get the network parameters unless you are familiar with network setup.
Date and Time
The radio will set your local time automatically after the internet connection is completed.
If you want to do manual setting, change it by the following options:
•
Time zone
Auto-set Time Zone: This option is set by default.
Manual-set Time Zone: Choose this option if you want to set the time in another region.
Choose and highlight the region/city you prefer and press OK to confirm.
Coupled with NTP (use network time) and DST (Daylight time saving) will be adjusted automatically if you choose to
use network time (NTP).
•
Set Time Format
Choose either 12-hour or 24-hour notation you prefer.
•
Set Date Format
•
DST (Day Light Saving)
Enable on/off
•
NTP (Use network time)
NTP is designed to synchronize a device's clock with a time server. Your radio will synchronize the time server by
default every time it powers up and connects to Internet.
This ensures a very high degree of accuracy in the radio's clock. You can change to use other time server by inputting
the URL address (see below NTP server). You can choose "Do not use network time" if you don't want it to.
If you choose not to use NTP for clock synchronization, highlight the NTP (Network time protocal) and press OK to
make the change. You will see the Set Date & Time appeared on the menu. Select it and adjust the date and time as
you desire.
•
NTP Server
NTP is designed to synchronize a device's clock with a time server. Here it shows the server being used for the radio.
Language
The default language is English, you can choose other languages as preferred. Scroll with the [▲ /▼] buttons on remote or
[Dial/Select] knob to the item with and press OK. Scroll to highlight and press [OK] to select your language of choice.
English, French, Spanish, Italian, German, Dutch, Polish, Russian and Simplified Chinese are available.
Local Radio
The radio is set by default to detect the radio stations in your local area automatically through internet connection and these
stations can be accessed by a press of [Local] button on remote. You can also set Local in another region if you want.
Highlight the Local Radio and press [OK]. Choose Manual-set Local radio to change the region setting.
Playback Setup
This is to set the mode of playback under UPnP/DLNA compatible streaming: Repeat All, Repeat Once or Shuffle.
12