Noise/Vibration Information - Würth master BS 10-A Instrucciones De Servicio

OBJ_BUCH-831-001.book Page 11 Thursday, November 27, 2008 8:58 AM
10 Screwdriver bit*
11 Securing screw for keyless chuck
12 Allen key*
Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our acces-
sories program.
Technical Data
Cordless Drill/Driver
Art. No.
Rated voltage
No-load speed
– 1st gear
– 2nd gear
Max. torque for
hard/soft screwdriving
application according to
ISO 5393
Max. drilling dia.
– Steel
– Wood
Max. screw dia.
Chuck clamping range
Drill spindle thread
Weight according to
EPTA-Procedure
01/2003

Noise/Vibration Information

Measured values determined
EN 60745.
Typically the A-weighted sound pressure level of the
product is less than 70 dB(A). Uncertainty K =3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values (triax vector sum) determined
according to EN 60745:
Drilling into metal: Vibration emission value
2
a <2.5 m/s , Uncertainty K =1.5 m/s
h
Screwdriving: Vibration
2
a <2.5 m/s , Uncertainty K =1.5 m/s
h
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is
used for different applications, with different acces-
sories or poorly maintained, the vibration emission
may differ. This may significantly increase the expo-
sure level over the total working period.
27.11.08
BS 10-A
0700 653 X
V= 10.8
-1 0 – 400
min
-1
min 0 – 1100
Nm 30/11
mm 10
mm 19
mm 7
mm 1.0 – 10
1/2"
kg 1.1
according to
2
,
emission value
2
.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the
exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in con-
formity with the following standards or standardiza-
tion documents: EN 60745 according to the
provisions of the directives
98/37/EC (until 28 Dec 2009), 2006/42/EC (from
29 Dec 2009).
Technical file at:
Adolf Würth GmbH & Co.KG, PFW,
D-74650 Künzelsau
Künzelsau, 31.07.2008
Adolf Würth GmbH & Co. KG
P. Zürn A. Kräutle
Battery Charging (see figure A)
❏ Use only the battery chargers listed on the
accessories page. Only these battery chargers
are matched to the lithium ion battery of your
power tool.
☞
Note: The battery is supplied partially
charged. To ensure full capacity of the bat-
tery, completely charge the battery in the bat-
tery charger before using your power tool for
the first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The Li-ion battery is protected against deep dis-
charging by the "Electronic Cell Protection (ECP)".
When the battery is empty, the machine is switched
off by means of a protective circuit: The inserted tool
no longer rotates.
Do not continue to press the
WARNING
On/Off
machine has been automatically switched
off. The battery can be damaged.
2004/108/EC,
switch after the
English–11