Oursson HB6010 Manual De Instrucciones página 15

Puree attachment .....................................................1 p c .
Whisk ........................................................................1 p c .
Multifunctional cup XL, 1,2L .....................................1 p c .
Cup's lid ....................................................................1 p c .
Pusher ......................................................................1 p c .
Working console .......................................................1 p c .
Grinding blade ..........................................................1 p c .
Cubic cutting attachment ..........................................1 p c .
Cleaning attachment.................................................1 p c .
Stainless steel chopping disk ...................................1 p c .
Stainless steel grater disk.........................................1 p c .
Measuring cup ..........................................................1 p c .
Instructions manual ..................................................1 p c .
ELEMENTS OF DESIGN, Рiс. В
Speed Switch
On / Off button
TURBO Mode button
Motor unit
Puree attachment
Whisk
Multifunctional glass cup XL
Cup's lid
Pusher
Working console
Chopping disk
11
Grater disk
12
Grinding blade
13
Opening for motor unit installation
14
Cubic cutting attachment
15
Cleaning attachment
16
Measuring cup
17
UTILIZATION, Рiс. C
Whisk.
Used for whipping egg whites, creams, biscuit dough,
dough for pancakes, stirring desserts.
• Insert the motor unit in the attachment and turn it
clockwise until it stops. Pic.C-1.
• Dip the whisk in a bowl with ingredients and turn on
the blender.
NOTE! For best results, whisk at a low speed, than
raise the speed. Whisk ingredients in small portions –
no more than 4 egg whites at once.
Puree attachment.
Used for soups-purees, baby food, pies and sauces.
• Insert the motor unit to the attachment and turn coun-
terclockwise until it stops. Рiс.C-1.
Multifunctional glass cup XL.
Used for installing chopping and grater disks and stain-
less steel blades.
• Place the cup on a dry and flat surface.
• Install the required attachment as shown in the Рiс.
C-2.
Chopping disk.
Used to cut ingredients in small slices.
• Install the cup into the working console.
• Install onto the console the chopping disk, selecting
small or large slices.
• Close the cup with the lid, using special clips on the
lid's sides.
• Install the motor unit into the special opening on the
cup's lid.
Grater disks.
Used for grating ingredients.
• Install the cup into the working console.
• Install onto the console the grater disk, selecting small
or large grater.
• Close the cup with the lid, using special clips on the
lid's sides.
• Install the motor unit into the special opening on the
cup's lid.
Cubic cutting attachment, Рiс.C-3
Used for cutting boiled/fresh vegetables and fruits into
cubes.
• Install the attachment
• Close the cup with the lid, using special clips on the
lid's sides
• Install the motor unit into the special opening on the
cup's lid.
Grinding blade.
Used for the preparation of baby food, mince, chop-
ping, nuts, making pates, butter with additions, chop-
ping onions, garlic and etc. Grinding blade is not in-
tended for liquid foods.
• Install grinding blade into the cup.
• Close the cup with the lid, using special clips on the
lid's sides
• Install the motor unit into the special opening on the
cup's lid.
Before first use, wipe the motor unit with a dry cloth.
Wash the cup, lid, pusher and attachments in a worm water
with some detergents. The time when the device idles must
not exceed 15 seconds.
The blades are very sharp, be careful.
• Before assembling or removing nozzles ensure that
the device is unplugged.
• Maximum time of continuous use of the device with a
whisk, chopper, grinding, grater and cubic attachment must
not exceed 1 minute, then you should turn off the blender
for 3 minutes.
• Maximum time of continuous use of the device with a
whisk must not exceed 10 minutes, then you must turn off
the blender for 30 minutes.
ORDER OF OPERATION:
1. Assemble the necessary attachment with the de-
vice as described above.
2. Plug in the device.
3. Select the required speed by setting its speed
switch. The blender has a smooth speed control
(from low speed to high.) Then press and hold the
on / off button.
4. You can also turn on the blender by holding down
the TURBO Mode. In this case, the device will
operate at maximal speed all the time. The speed
will not change even if you change the position of
the switch.
5. To switch off, release the TURBO Mode.
6. Unplug the power cord from the outlet.
7. Remove the motor unit.
into the cup .
15