Chicago Pneumatic CP8750 Manual Del Operador página 7

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

To reduce the risk of injury, always unplug your
tool before performing any maintenance. Never
disassemble the tool or try to do any rewiring on
the
tool's
electrical
MILWAUKEE
service facility for ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check
for loose screws, misalignment, binding of moving parts, improper mount-
ing, broken parts and any other condition that may affect its safe opera-
tion. If abnormal noise or vibration occurs, turn the tool off immediately
and have the problem corrected before further use. Do not use a dam-
aged tool. Tag damaged tools "DO NOT USE" until repaired
(see "Repairs").
Under normal conditions, relubrication is not necessary until the motor
brushes need to be replaced. After six months to one year, depending on
use, return your tool to the nearest MILWAUKEE service facility for the
following:
Lubrication
Brush inspection and replacement
Mechanical inspection and cleaning (gears, spindles, bearings,
housing, etc.)
Electrical inspection (switch, cord, armature, etc.)
Testing to assure proper mechanical and electrical operation
Chicago Pneumatic Tool Company Limited Warranty and Service Policy
Products of the Chicago Pneumatic Tool Company ("CP") are warranted to be free from defects in material and workmanship for one year from the date of
purchase. This warranty applies only to Products purchased new from CP or its authorized dealers. Of course this warranty does not apply to Products
which have been abused, modified, or repaired by someone other than CP or its Authorized Service Representatives.
If a CP Product proves defective in material or workmanship within one year after purchase, return it to any Authorized Service Center
prepaid, enclosing your name and address, adequate proof of date of purchase and a short description of the defect. CP (or its affiliate) will, at its option,
repair or replace defective Products free of charge. Repairs or replacements are warranted as described above for the remainder of the original warranty
period. CP's sole liability and your exclusive remedy under this Warranty is limited to repair or replacement of the defective Product.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, OR CONDITIONS, WRITTEN OR ORAL, EXPRESSED OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, ALL WARRANTIES OR CONDITIONS, OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, ALLOF WHICH ARE HEREBY DISCLAIMED. THERE SHALL BE NO LIABILITY FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES, OR ANY OTHER DAMAGES, COSTS OR EXPENSES, EXCEPTING ONLY THE COST OR EXPENSE OF REPLACEMENT OR REPAIR.
Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty. This warranty gives
specific legal rights. Consumers may have other rights under state or federal law.
*
CP Products described in this manual may be sent to any MILWAUKEE ELECTRIC TOOL CORPORATION Branch Office/Service Center or
Authorized MILWAUKEE Service Station for repair. See back page for information on how to locate a facility nearest you.
WARNING!
system.
Contact
a
Chicago Pneumatic Tool Company
Rock Hill, South Carolina 29730-7463
MAINTENANCE
To reduce the risk of injury, electric shock and
damage to the tool, never immerse your tool in
liquid or allow a liquid to flow inside the tool.
Cleaning
Clean dust and debris from vents. Keep the tool handles clean, dry and
free of oil or grease. Use only mild soap and a damp cloth to clean your
tool since certain cleaning agents and solvents are harmful to plastics
and other insulated parts. Some of these include: gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia. Never use flammable or
combustible solvents around tools.
Repairs
If your tool is damaged, return the entire tool to the nearest service
center listed on the back cover of this operator's manual.
WARRANTY
1800 Overview Drive
WARNING!
*
transportation
page 7

Publicidad

Tabla de contenido
loading

Tabla de contenido