Technical Data; English - Chicago Pneumatic CP 8210 Instrucciones De Uso

TECHNICAL DATA

Nominal power.........................................................................
Rated output ............................................................................
No-load speed .........................................................................
Max. no-load speed .................................................................
Thread of work spindle ............................................................
Weight .....................................................................................
Typical weighted acceleration in the hand-arm area ...............
Typical A-weighted sound levels:
Sound pressure level ............................................................
Sound power level ................................................................
Wear ear protectors!
Measured values determined according to EN 50 144.
SAFETY INSTRUCTIONS
Please pay attention to the safety instructions in the
attached leaflet!
Appliances used at many different locations including open
air must be connected via a current surge preventing switch.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
After switching off, the machine will not be idle immediately.
(After-running of the work spindle.) Allow the machine to
come to a stop before putting down.
Never reach into the danger area of the plane when it is
running.
Always use the auxiliary handle.
Only use tools whose permitted speed is at least as high as
the highest no-load speed of the machine.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine
in order to find out the cause.
Due care should be taken that no sparks or sanding dust
flying from the workpiece come into contact with you.
The adjusting nut must be tightened before starting to work
with the machine.
The workpiece must be fixed if it is not heavy enough to be
steady. Never lead the workpiece to the grinding disk with
your hand.
SPECIFIED CONDITIONS OF USE
The polisher can be used for polishing lacquers, coatings,
plastics and other smooth surfaces.
Do not use this product in any other way as stated for
normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is
in conformity with the following standards or standardized
documents. HD 400, EN 50144, EN 55014-1, EN 55014-2,
EN 61000-3-2, EN 61000-3-3, in accordance with the
regulations 98/37/EC, 73/23/EEC, 89/336/EEC
Yves Antier
General Manager
5

ENGLISH

CP 8210
.......................1200 W .........................1200 W
.........................600 W ...........................600 W
................900-2500 /min.............. 900-2500 /min
.......................4100 /min......................4100 /min
.......................M 14 ............................M 14
..........................2,1 kg............................2,1 kg
.......................< 2,5 m/s .....................< 2,5 m/s
2
...........................82 dB (A) ......................82 dB (A)
...........................95 dB (A) ......................95 dB (A)
MAINS CONNECTION
Connect only to a single-phase AC current supply and only
to the mains voltage specified on the rating plate.
Connection to sockets without earth protection is possible
as the appliance features protective insulation to DIN 57
740/ VDE 0740 and CEE 20. Radio suppression complies
with the European standard EN 55014.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Chicago Pneumatic accessories and spare parts.
Should components need to be exchanged which have not
been described, please contact one of our Atlas Copco
service agents (see our list of guarantee/service
addresses).
If needed, an exploded view of the tool can be ordered.
Please state the Article No. as well as the machine type
printed on the label and order the drawing at your local
service agents or directly at: Atlas Copco Electric Tools
GmbH, Postfach 320, D-71361 Winnenden.
ELECTRONICS
The speed of rotation is adjusted electronically when the
load increases.
In case of a longer overload period the speed is decreased
electronically. The machine continues to run slowly to cool
down the motor coil. After switching off and on the machine
can be used at rated load.
SYMBOLS
Always disconnect the plug from the socket
before carrying out any work on the
machine.
Accessory - Not included in standard
equipment, available as an accessory.
CP 8210 E
2