DeWalt DPN9033-XJ Manual Del Usuario página 9

DPN90C-XJ / DPN75C-XJ / DPN64C-XJ
1. Open the magazine: Pull down on the latch and swing
the door open. Swing magazine cover open. (Fig. 4)
2. Check adjustment: the nailer must be set for the length
of nail to be used. Nails will not feed smoothly if the
magazine is not correctly adjusted.
To change the setting:
The magazine contains an adjustable nail platform on which
the nail coil rests.
The nail platform can be adjusted up and down to three or
4 nail settings. To change settings, pull up on the post and
twist to the correct step. (Fig. 5)
Step DPN90C-XJ
1 50-65mm
2 70-75mm
3 80-90mm
4 -
3. Load the coil of nails: Place the coil of nails over the
post in the magazine. Uncoil enough nails to reach the
feed pawl. Place the first nail in front of the front tooth
on the feed pawl, in the driver channel. The nail heads
must be in the slot in the nose. (Fig. 6)
4. Swing the door/magazine cover closed. Check that the
latch engages when released. (If it does not engage,
check that the nail heads are in the slot in the nose.)
NOTE: DPN64C-XJ / DPN75C-XJ ONLY
Removal of plastic strip: As nails are driven, the plastic
strip will feed out of the tool. When sufficient strip has
been fed out, it can be torn away by pulling against the
tear edge in the nose. (Fig. 7)
REMOVING NAILS (DPN9033-XJ /
DPN9033SM-XJ)
1. Disconnect the tool from the air supply
2. Pull pusher back until it is securely engaged (Fig. 8)
3. Slide nails back to opening and push out
CAUTION: The pusher and pusher spring (constant
force spring).
DPN64C-XJ DPN75C-XJ
32-40mm 38-40mm
45-50mm 45-50mm
55-64mm 55-60mm
- 65-75mm
Caution must be used when removing nails, as if
pusher is disengaged from latch it could spring
forward potentially pinching your hand.
Extra caution should be taken when carrying out
maintenance on the magazine area of the tool. The
spring is wrapped around but not attached to a roller.
If the spring is stretched beyond its length, the end
will come off the roller and the spring will roll up with
a snap, with a chance of pinching your hand. Also the
edges of the spring are very thin and could cut your
hand. Care must also be taken to insure no permanent
kinks are put in the springs as this will reduce the
springs force.
GUIDE ROD INSTALLATION AND REMOVAL
(DPN9033-XJ / DPN9033SM-XJ)
Step 1 (Fig.. 9): Locate guide (A); Pull and rotate cover
(B).
Step 2 (Fig.. 10): Locate access windows for installation
and removal of guide rod (C); Locate guide rod storage
channel (D); Rotate cover open to install or remove guide
rod (E); Install or remove guide rod through rear
of magazine (F).
Step 3 (Fig.. 11): Install guide rod through (G) for 2.8mm
to 3.3mm shank nails. Rotate cover (B) to close; Install
guide rod through (H) for 3.3mm to 4.1mm shank nails.
Rotate cover (B) to close.
FASTENER DEPTH CONTROL ADJUSTMENT
DPN9033-XJ / DPN9033SM-XJ / DPN90C-XJ
(Fig.. 12)
The Fastener Depth Control Adjustment feature provides
control of the nail drive depth from flush with or just above
the work surface to shallow or deep countersink.
Warning! Disconnect tool from air supply before
attempting any parts disassembly and before changing the
work contacting element adjustment.
1. Push in Locking Button
2. Adjust contact arm up to increase depth of drive or
down to decrease it.
3. Release locking button.
EN GL I SH EN GL I SH
7 7