Six-Monthly Maintenance; Splash Guard Replacement; Troubleshooting Guide; The Suction Motor Does Not Work - Floorpul ruby 45e Manual De Uso Y Mantenimiento

GB
6. Replace the front rubber.
7. To reassemble the squeegee repeat reverse the
operations above-mentioned.

SIX-MONTHLY MAINTENANCE

SPLASH GUARD REPLACEMENT

1. Release the spring in the rear part of the brushes
base group from the slot placed at the extremity of
the metal strip.
2. Unscrew the nut on the front part of the brushes
base group and take off the metal strips.
3. Replace the splash guard rubbers and follow the
assembling instructions at "SPLASH GUARD ASSEM-
BLY" paragraph.
With brushes assembled, the splash guard must
slightly touch the floor.
The checking of all the other foreseen machine
operations is left to the authorized technical as-
sistance.

TROUBLESHOOTING GUIDE

THE SUCTION MOTOR DOES NOT WORK

1. Verify that the signal light for presence of the
tension (5) is on, if necessary, check that the plug is
correctly inserted in a functioning mains socket.
2. The model equipped with the key switch (see un-
der "OPTIONAL ACCESSORIES"), turn the key (8)
clockwise to switch on the machine.
3. Verify that the switch (2) is on.
If the problem persists, please contact the authorized
technical assistance.

THE BRUSHES MOTOR DOES NOT WORK

1. Verify that the signal light for presence of the
tension (5) is on, if necessary, check that the plug is
correctly inserted in a functioning mains socket.
2. The model equipped with the key switch (see un-
der "OPTIONAL ACCESSORIES"), turn the key (8)
clockwise to switch on the machine.
3. Verify that the switch (1) is on.
4. Activate the levers for presence (9).
5. Check that the brushes motor overload protec-
tion device (7) did not intervene; in this case, rearm
it.
If the problem persists, please contact the authorized
technical assistance.
ATTENTION:
Never leave the socket inserted in the mains plug
when the machine is not being used.

INSUFFICIENT WATER ON THE BRUSHES

1. Check that the solution valve lever (10) is open.
2. Check the level of the liquid in the solution tank.
3. Check that solution filter (1) is clean.
4. If the machine is equipped with the solenoid
valve (see under "OPTIONAL ACCESSORIES"), act
upon the levers presence (9).
5. The model equipped with the key switch (see un-
der "OPTIONAL ACCESSORIES"), turn the key (8)
clockwise to switch on the machine.
If the problem persists, please contact the authorized
technical assistance.

THE MACHINE DOES NOT CLEAN PROPERLY

1. The brushes do not have the suitable bristle di-
mension: use only original brushes. For advice, con-
tact the authorized technical assistance.
2. The brushes have got worn bristles. Check the
brushes wear condition and eventually replace them
(the brushes have to be replaced when the bristles
have reached a height of about 15mm).
To replace the brushes, see instructions at paragraph
"BRUSHES DISASSEMBLY" and "BRUSHES ASSEMBLY".
3. The solution detergent is insufficient: open more
the solution valve.
4. Check that the liquid detergent is in the recom-
mended percentage.
Contact the authorized technical assistance for ad-
vice.

THE SQUEEGEE DOES NOT DRY PERFECTLY

1. Check that the squeegee rubbers are clean.
2. Check the height and inclination of the squeegee
(see section "SQUEEGEE" in "BEFORE USE").
3. Check that the suction hose is correctly inserted
in the proper seat on the recovery tank.
4. Clean the suction filter.
5. Replace the rubbers if worn out.
6. Check that the suction motor switch is on.
7. Check that the recovery tank is empty.
21

EXCESSIVE FOAM PRODUCTION

Check that low foam detergent has been used. Even-
tually add small quantities of anti foam liquid into
the recovery tank.
Please be aware that a bigger quantity of foam is
produced when the floor is not very dirty. In this
case please dilute detergent solution.
GB