GN Netcom GN 6110 Manual Del Usuario página 18

Declaration
This product is CE marked according to the provisions of the R & TTE Directive (99/5/EC). Hereby, GN Netcom as declares that this
product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Please note that this product uses radio frequency bands not harmonised within EU. Within the EU, this product is intended to be used
in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden,
United Kingdom and within EFTA in Iceland, Norway and Switzerland.
• Never try to dismantle the product yourself. None of the internal components can be replaced or repaired by users.
• Avoid exposing the product to rain or other liquids.
• The headset may become warm during battery charging. This is normal and will not affect the safety or performance of the head-
set.
If you have any problems or questions regarding the product, please contact your reseller or go to http://www.gnnetcom.com
There is an international patent pending for the GN 6110 and its elements.
USA FCC part15
FCC Notice to Users/Product Statements
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
Users are not permitted to make changes or modify the device in any way. Changes or modifi cations not expressly approved by GN
Netcom will void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following mea-
sures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user must place the base at least 8" (20cm) or more from any personnel and must not be co-loaded or operating in conjunction
with any other antenna or transmitter in order to comply with FCC RF exposure requirements.
USA FCC part68
FCC Notice to Users/Product Statements
1. This equipment is compliant with part 68 of the FCC Rules. On the equipment is a label that contains, among other information,
the FCC registration number for this equipment. If requested, this information must be provided to the telephone company.
2. The device may not be connected directly to the telephone network, but must connect to a FCC registered telephone.
3. If this device is malfunctioning, it may also be causing harm to the telephone network. The device should then be disconnected
until the source of the problem can be determined and until repair has been made. If this is done, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the tele-
phone company will notify the customer as soon as possible. Also, you will be advised of your right to fi le a complaint with the FCC
if you believe it is necessary.
4. The telephone company may make changes in its facilities, equipment, operations and/or procedures that may affect the operation
of this equipment. If this happens, the telephone company will provide advanced notice in order for you to take the necessary steps
to maintain uninterrupted service.
5. If the telephone company requests information on what equipment is connected to their lines, inform them of:
(a) The telephone number that this unit is connected to.
(b) The FCC Registration number located on the label.
Canada
IC Notice to Users/Product Statements
Operation is subject to the following two conditions:
(1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause
undesired operation of the device.
The term "IC:" before the certifi cation/registration number only signifi es that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifi cations were met. It does not imply that industry Canada approved the
equipment
Canada Terminal equipment
IC Notice to Users/Product Statements
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifi cations. This is confi rmed by the
registration number.
18
GN6110_contents_EU_13-02-2004.indd 18 16-02-2004, 11:10:58