Instructions For Operation; Maintenance And Service - stayer MULTI GARDEN 18 Manual De Instrucciones

4.4. Nylon thread.
4.5. Thread spool.
4.6. Thread spool button.
Notice. The edge trimmer accessory (fig. 4) must operate
with the extension bar (fig. 3). Insert the plug of the end
(3.11) of the extension bar into the inlet (4.1) in the
device in accordance with the track position, by the
notch with the side of the notch turned downwards, until
it fits. Insert the battery into the battery position (3.5).
Otherwise, you will not be able to work. After finishing
work, push the lock button (4.2) by means of which you
can release the extension bar of the edge trimmer. Pull
out the plug form the end (3.11) of the extension.
Attention: Remove the battery from the machine before
changing the blades or adjustment tool.
1. Assembly of the protector.
Insert the protector (4.3) into the fitting condenser using
the screws as included. (Fig. H)
CAUTION.
· During this operation you must be careful with the
blade of the wire cutter. You may injure yourself.
Warning:
· Never use the edge trimmer without the protector
(4.3). This is vital for your safety and that of other
persons, and for the good performance of the
cutter.
Non compliance with these safety rules is not only
dangerous but is also invalidates the guarantee terms.
2. Before using the edge trimmer, check that the nylon
thread (4.4) contacts or passes over the thread cutting
blade. The nylon thread (4.4) will be automatically cut
when it rotates.
If the nylon thread does not reach the required length,
press the thread spool button (4.6) and make the
machine rotate without load so that the length of the
thread is adjusted automatically.
Replacement of the thread spool. (Fig. I)
Warning:
·In no case must there be added thread to the empty
spool; it must be replaced by a new one. The use of
cables having characteristics that differ from the
original ones may damage the grass cutter
permanently and as well invalidate the guarantee
terms.
3. Start slowly – when you have the acquired experience,
you will be able to use the whole potential of the lawn
trimmer. Initiate the lawn trimming process
progressively. (Fig. J)
· Trim the lawn by moving the edge trimmer from the right
to the left and maintain the soft movement of the trimmer
inclined by about 30o.
· When the grass is tall, it must be cut by layers, always
from the upper portion. Cuts must be short.
· Do not cut humid or wet grass – when it is dry excellent
ENGLISH
16
results will be achieved upon cutting.
· Take into account the recommendations given as, if you
expose the machine to excessive operation or if you
force it, it may get damaged and overload the fitting
condenser, thereby achieving malfunctioning or directly
that the machine switches off.

4. Instructions for operation

Change of tools/tool positions
1. Blade prepared for cutting hedges. (Fig. K)
2. Shears for cutting lawn, branches. (Fig. L)
3. Blade prepared for pruning. (Fig. M)
4. Lawn trimmer with shears and extension handle.
(Fig. N)
5. Hedge cutter for working at heights (Fig. Ñ)
6. Prepared for cutting grass. (Fig. O)
Warning:
· Keep your hands and fingers away from the movable
parts. Any part of the body entering in contact with the
movable parts may be seriously injured.
· Before starting to work, make sure that the area to be
trimmed is free of stones, scrap, wires and other
objects.
· It is recommended to work with sufficient light –
preferably work in the daytime, if not so use powerful
artificial light.
It is recommended to work with sufficient light –
preferably work in the daytime, if not so use powerful
artificial light.
DANGER
When the blade becomes clogged by any electric cable
or line, DO NOT TOUCH THE BLADE! IT MAY CARRY
ELECTRICITY – this is very dangerous. Drop unit in the
most careful possible way. Remove the battery or the
extension handle from the device. If you do not pay
attention to this waning, you may become seriously
injured (death hazard).

5. Maintenance and service

Regarding the batteries, pressing the release button
Ÿ
before eliminating obstructions, revising, cleaning or
working.
Keep all nuts, bolts and screws tightened to make sure
Ÿ
that the shears and blades are in safe working conditions.
Regularly check and replace blades that are worn-out or
Ÿ
damaged by use.
Always mount the protection when transporting or storing
Ÿ
the machine.
To facilitate operation and extend the lifetime of the blade,
Ÿ
lubricate the cutting device before and after each use.
Before lubrication, remove the battery; carry out the
operation on a flat surface. Apply lightweight machine oil
along the edge of the upper blade with a smooth brush or
cloth with lubricating oil.
16