Temperature Setting; Fan Speed Setting; Navigating Through The Main Menu - Mitsubishi Electric Mr. SLIM PKA-A Serie Manual De Instrucciones

3. Operation

3.3. Temperature setting

<For wired remote controller>
<Cool, Dry, Heat, and Auto>
Fri
83ºF
Room
Cool Set temp. Auto
83
ºF
Mode Temp. Fan
F1 F2 F3 F4
Press the [F2] button to decrease the preset temperature, and press the
[F3] button to increase.
• Refer to the table on page 6 for the settable temperature range for dif-
ferent operation modes.
• Preset temperature range cannot be set for Fan/Ventilation operation.
• Preset temperature will be displayed either in Centigrade in 0.5- or
1-degree increments, or in Fahrenheit, depending on the indoor unit
model and the display mode setting on the remote controller.
<For IR wireless remote controller>
To decrease the room temperature:
Press button 3 to set the desired temperature.
The selected temperature is displayed
To increase the room temperature:
Press button 3 to set the desired temperature.
The selected temperature is displayed

3.4. Fan speed setting

<For wired remote controller>
Fri
Room 83ºF
Cool Set temp. Auto
83
ºF
Mode Temp. Fan
F1 F2 F3 F4
Press the [F4] button to go through the fan speeds in the following order.
Auto
• The available fan speeds depend on the models of connected indoor
units.
<For IR wireless remote controller>
Press the Fan Speed button as many times as necessary while the
system is running.
• Each press changes the force. The currently selected speed is
shown at display.
Note:
The number of available fan speeds depends on the type of unit
connected.
In the following cases, the actual fan speed generated by the unit
will differ from the speed shown the remote controller display.
1. When the unit is in STANDBY or DEFROST states.
2. When the temperature of the heat exchanger is low in the heat-
ing mode. (e.g. immediately after heating operation starts)
3. In HEAT mode, when room temperature is higher than the tem-
perature setting.
4. When the unit is in DRY mode.
Fri
84ºF
Room
Cool Set temp. Auto
84
ºF
Mode Temp. Fan
Example display
(Centigrade in 0.5-degree increments)
3
.
3
.
■ Automatic fan speed setting (For IR wireless remote controller)
It is necessary to set for wireless remote controller only when automatic
fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic fan
speed at default setting.
1 Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
blinks and Model No. is lighted A
MODEL SELECT
2 Press the AUTO STOP
button.
blinks and setting No. is lighted B
(Setting No.01: without automatic fan speed)
3 Press the temp.
buttons to set the setting No.02.
(Setting No.02:with automatic fan speed)
If you mistook the operation, press the ON/OFF
again from procedure 2.
4 Press the SET button with something sharp at the end.
and Model No. are lighted for 3 seconds, then turned off.
MODEL SELECT
MODE
CHECK
TEST RUN
14
3.5. Airfl ow up/down direction setting
<For wired remote controller>

3.5.1 Navigating through the Main menu

<Accessing the Main menu>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
<Item selection>
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Cursor
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
<Navigating through the pages>
page
Main Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor Page
F1 F2 F3 F4
.
.
button and operate
B
MODEL SELECT
A
ON/OFF TEMP
3
FAN AUTO STOP
2
VANE AUTO START
5
LOUVER h
min
SET RESET CLOCK
Press the [MENU] button.
The Main menu will appear.
Press [F1] to move the cursor down.
Press [F2] to move the cursor up.
Press [F3] to go to the previous
page.
Press [F4] to go to the next page.
7